History on ohm A's and F's.


I panned through the threads and read how the old ohm a's were remarkable.
Would like to hear more about this and other ohm speakers.
pedrillo
Lewis,

There is a transition from wave bending at higher frequencies to pistonic at lower, I believe.

Not sure I'd call it a "crossover" necessarily. Not sure to what extent that transition is audible or discernible to the human ear. Maybe others might know more?

The F driver had three separate sections covering different frequencies with different materials comprising each section. I believe I've heard reference to the 2 cut-over points between sections referred to as the physical equivalent of an electronic crossover, similar function, totally different technology/approach.

Also it is not clear to me the exact specifications in regards to at what frequencies and to what extent at each the driver operates pistonically versus bending wave.

I think it would be accurate to say that the modern Walsh drivers used by OHM operate more in the pistonic mode than wave bending in that wave bending is associated with higher frequencies I believe and the modern OHM CLS Walsh drivers use a supplementary tweeter. German Physics DDD drivers on the other hand operate at the high end of the frequency spectrum supplemented for the most part by conventional woofers, I believe, which is an opposite approach.

Getting a single Walsh driver to do it all or as much as possible without destroying itself at high SPLs would seem to be the name of the game in general.
Lewis,

Without presuming too much technical knowledge of my own, I suspect that the opposite happens. Since the dispersion pattern of the Ohms is always (nearly) omnidirectional, there is a sense of "continuousness" to the speakers. Whatever discontinuity that might be a result of your observation seems to be subsumed by this effect. At least to my ear.

Also, I would guess that the transition may be gradual, with some frequencies being partially reproduced by both bending and pistonic motion. Such an arrangement would be akin to very low order (presumably well less than first order) crossover. Such schemes usually mask transitional issues, although they can certainly introduce other artifacts. By the time response is primarily pistonic, you may well be at a frequency low enough that most listener's sensitivity is reduced. Similarly, BTW, the cross to the tweeter is so high in frequency that -IME- most listeners will be relatively insensitive to that hand-off.

Maybe John S can comment further.
YEs, I'd really love to understand the pistonic/wave bending thing in more detail in regards to the CLS Walsh driver.

OHM CLS must be doing some wave bending in the mid range and up, though clearly not at the very top end where the super tweet works. The cls high end response extends beyond 16-17Khz which I think is approximately where the F ended.

I'm assuming wave bending is at least part of what propagates sound outward horizontally from the rear of the downward firing cone as opposed to up/down (pistonic) using the cabinet to tune the low end, but I do not know for sure, just how smooth, dynamic and "coherent" the resulting sound is, particularly in the mid-range. The very generalized diagrams I've seen on the OHM site showing how the CLS driver works seem to indicate this.
I sent an email to Dale Harder who rebuilds classic Ohms and now manufacturers brand new A & F equivalents(HHR Exotic Speakers) with a number of modern improvements. He may be one of the only people who can properly answer that question.

Hopefully, he'll be able to chime in with some good info
Dale did chirp in on this thread earlier regarding his designs and German Physiks specifically and his comments are worth repeating here.

Though their Walsh driver designs all vary, I suspect what he says regarding how each are similarly voice coil driven regardless of resulting pistonic or bending wave propogation of sound applies to the OHM CLS as well, but this is just my assumption based on what appears to be similar physics and design elements in play in the case of each.

Dale said:

"Bending wave schmendig wave…piston schmiston…it’s just a matter of semantics at best. So what if the GP vc is elastomerically connected or mine is hard fixed. I can do that with silicone. Bottom line, the vc still controls the movement of the cone and the cone is launched forward in a bending wave fashion or a pistonic fashion depending upon the wavelength. Additionally, the mass of the vc controls the upper end and transient response. GP still uses an Aluminum edge wound vc same as mine. And both drivers are made of Titanium foils exactly the same size. T/S parameters still apply as well."

IMHO, each vendors Walsh design varies based on targeted market.

GP targets the very high end audio market.

Dale Harder is a champion of the concepts of Lincoln Walsh's driver and is a champion of carrying the original OHM designs into the future with a focus on quality and value.

OHM has always and continues to focus on providing the best sound possible as cost effectively as possible to the masses.