Is it possible to have vinyl nearly noise free?

"Noise free" records?

When I started buying records again, about three years ago, the constant ticks and pops were driving me crazy - to the point where I was ready to give up...

I went through the various processes - DIY formula and various scrubbing techniques. Got a spin clean, hoping that would help, but no, still noise there.

Picked up an Okki Nokki, least expensive vacuum RCM I could find. After much trial and error, I am finally happy with the state of my records.

Took a while, but got the process figured out so iy works for me. Disc Doctor brushes, distilled water and L'Art du Son fluid. Three brushes, one for wash and two for rinse. I do two wash cycles where I let the cleaner soak for 5 min before doing a "thorough, but light scrub" and then two rinse cycles. Separate wands for wash/clean. I only do one rotation to remove the fluids until the final rinse, when I do two.

Have to say I am super happy w the results. Now, gotta tackle the static issue.

I am curious about the Phono Stage causing ticks and pops. Have read a bit about this and don't quite get how it actually works in practice. The profile of the stylus seems pretty straight forward. The sharper it is, the deeper into the grooves it goes and the less the top part of the groove - the noisiest part - doesn't have as much contact w the stylus.

P

Use a Zero-Stat on the record just before play. Use Static-Guard https://www.walmart.com/ip/Static-Guard-Spray-5-5-Ounces/21092566
Puff a little around (not directly over) the turntable. Waft a little around the phono leads, phono stage, and over all interconnects and speaker cables. Between the conditions in my room and how keen I am on SQ I do this before every side. Its not like it gets real bad and I hear zapping if I don't do it as often. But if I skip a side or two and then spray there is a rather obvious improvement in terms of a little less grain and a lower noise floor. This stuff is cheap, I don't mind the smell, and I never ever hear or see any static zapping or popping anywhere when I do this.

The improvement spraying the cables tells me static isn't just a problem when records pop. Its everywhere. Cable Elevators get them up off the floor and work great. Same for power cords and interconnects. None of this was done because anyone said so. I only do what I myself have tested and proven to be worth doing. This stuff is dirt cheap. So don't take my word for it either. Just try if you want and see for yourself.

Atmasphere...
Can you recommend some stand-alone phono stages that have the design features you describe? Don’t think I’m smart enough to figure that out for myself, but it would be interesting to give one a try. Thanks!

@mrdecibel 

"What was frightening, we saw little pieces of the record vinyl being torn away from the record, as the stylus passed over. Like rubber off a tire, but reversed ( the record was the road )."

Yes, the velocities and forces in action are huge. Therefore it's safe to say tracking ability is what counts most. Of course its a complicated business but isn't everything in audio? Or even life?  

The following article on tracking may be of interest but 5 minutes or so of meditation beforehand may be needed due to the complexity involved.

http://www.phaedrus-audio.com/further_tracking.htm

Can you recommend some stand-alone phono stages that have the design features you describe? Don’t think I’m smart enough to figure that out for myself, but it would be interesting to give one a try. Thanks!

I know Nelson Pass makes a stable phono section; not sure if its a stand-alone product or not. IME a simple way to sort it out is to see if installing a "cartridge loading" (its really 'detuning') resistor makes the sound different. If not, then the phono section is probably stable.
FWIW Jonathan Carr and I had a nice conversation about this topic at Munich a few years ago. There was a nice thread on the What's Best forum about cartridge loading in which he was active (his moniker was JCarr) that goes into the 'cartridge loading' aspect of this issue in some depth. The advantage of not having to load the cartridge that he brought up with me was the simple fact that energy has to come from somewhere, so loading the cartridge with a low resistance was going to make the cantilever stiffer and less able to track higher frequencies. He and I have both written a lot about this topic; its pretty obvious that I simply have to post an article on our website that goes into it with more depth so I don't have to keep repeating myself.