Hi Guys, I need some advice, i am talking to a guy who has some mmg's for sale. they look very good and i have heard them. but my only concern is that someone told me that they have a issue with the adhesive and in due time they will rattle, does anyone know of this issue with them,i don't want to soak money into a pair of soon to be rattling speakers, also is there any way you can tell the year they where made? other then calling magnepan. Thank's
Magnepans
I'm kinda new to the plannar/magnepan world, but I am really interested in trying out a pair after all the reviews I've been reading. From what I understand these speakers are quite power hungry. What is the minimum I need to properly drive these?
I currently have a VAC Avatar integrated tube amp. These are the stats:
Type: Integrated vacuum tube amplifier with MM phono stage and home theater (direct power amplifier) mode.
Tube Complement: two 12AX7 low noise (phono), two 12AX7 (line stage), three 12AU7/6189A (power amplifier), and four EL34 (power amplifier)
Options: Remote control for volume (motorized direct control) & mute
Power amplifier ("Home Theater" direct mode):
Output matching: 4 or 8 ohms nominal
Power output: 60 watts/channel ultra-linear; 27 watts/channel triode
Frequency response: 9 Hz - 35 kHz +0 / -0.5 dB, 3 Hz - 71 kHz +0 / -3.0 dB
Power bandwidth: 11 Hz - 63 kHz + 0 / -3.0 db ref. 50 watts
Gain: 25 dB ultra-linear; 23 dB triode
Residual noise: 1.5 mv at 8 ohm output
Channel separation: -72 dB @ 1 kHz; -60 dB @ 10 kHz
Line stage preamplifier:
Gain: 24 dB
Maximum input signal: Infinite (attenuation precedes line stage)
Noise contribution: Approx. 0.1 mv at power amplifier output
THD contribution: Approx. 0.04%
Tape output: Unity gain from selector, non-inverting
Phono stage preamplifier:
Gain: 37 dB (measured at tape output)
MC phono stage in place of the MM optional
Residual noise: 3 mv at output (S/N ratio approx. 69 dB)
Overload: 117 mv @ 1 kHz = 8 volts RMS output, 460 mv @ 10 kHz
Frequency response: RIAA +/- 0.25 dB
Notes: Does not invert absolute phase.
Anyone know if these will do or if I'll have to upgrade? Love the tube sound . . . will I need to go solid state for Maggies? Thanks for putting up with the noobie question :)
I currently have a VAC Avatar integrated tube amp. These are the stats:
Type: Integrated vacuum tube amplifier with MM phono stage and home theater (direct power amplifier) mode.
Tube Complement: two 12AX7 low noise (phono), two 12AX7 (line stage), three 12AU7/6189A (power amplifier), and four EL34 (power amplifier)
Options: Remote control for volume (motorized direct control) & mute
Power amplifier ("Home Theater" direct mode):
Output matching: 4 or 8 ohms nominal
Power output: 60 watts/channel ultra-linear; 27 watts/channel triode
Frequency response: 9 Hz - 35 kHz +0 / -0.5 dB, 3 Hz - 71 kHz +0 / -3.0 dB
Power bandwidth: 11 Hz - 63 kHz + 0 / -3.0 db ref. 50 watts
Gain: 25 dB ultra-linear; 23 dB triode
Residual noise: 1.5 mv at 8 ohm output
Channel separation: -72 dB @ 1 kHz; -60 dB @ 10 kHz
Line stage preamplifier:
Gain: 24 dB
Maximum input signal: Infinite (attenuation precedes line stage)
Noise contribution: Approx. 0.1 mv at power amplifier output
THD contribution: Approx. 0.04%
Tape output: Unity gain from selector, non-inverting
Phono stage preamplifier:
Gain: 37 dB (measured at tape output)
MC phono stage in place of the MM optional
Residual noise: 3 mv at output (S/N ratio approx. 69 dB)
Overload: 117 mv @ 1 kHz = 8 volts RMS output, 460 mv @ 10 kHz
Frequency response: RIAA +/- 0.25 dB
Notes: Does not invert absolute phase.
Anyone know if these will do or if I'll have to upgrade? Love the tube sound . . . will I need to go solid state for Maggies? Thanks for putting up with the noobie question :)
- ...
- 85 posts total
- 85 posts total