Musician vs. audiophile

I have a friend who studied music in University and composes classical pieces.  When he hears a classical piece of music, he appreciates how it was composed, the methods used by the composer in writing this piece. When I talk about HiFi he covers his ears, when I explained about PRAT he thought I was utterly mad.  We both like music also classical music, if I like a particular piece of music its purely from the music, if he likes the same piece of music, its because of the music and how it was written. He is not so concerned how the music is presented (HiFi) but much more interested as to the music itself and how it was composed.  Often he would say 'notice how the composer expanded on that one note or theme'  I sometimes think about famous musicians of all genres, apart from the recording equipment used in studios do they posses HiFi at home. Does Paul McCartney have a state of the art Ayre system at home or does Mick Jagger have a Naim statement at home or are musicians not so bothered about HiFi...?

Repeter,
I believe most if not all BAT power amplifiers have input impedances of 100K ohms. It seems this shouldn’t be an issue matching their sibbling preamps regarding Al’s earlier caution. You'd think the manufacturer would make these family components compatible.  I could be wrong in this assumption. 
Charles

Charles1dad 12-30-2017
I believe most if not all BAT power amplifiers have input impedances of 100K ohms.

Right you are, Charles, as usual!

Repeter, as Charles indicated the input impedance of your amplifier is spec’d at 100K (much higher than the input impedances of the majority of solid state amps). And the input impedances of many and perhaps most JL subs are spec’d at 50K unbalanced/10K balanced. So provided that you are using balanced connections between the preamp and power amp and unbalanced connections to the subs impedance compatibility is probably not the **major** contributor to the issue. Although it nevertheless is probably contributing significantly to the bass issue you described, given the **extremely** high 14K balanced output impedance of the preamp at 20 Hz (assuming the Six-Pak option is not installed), and given that the 100K and 50K loads together constitute a load of 33K. 33K/14K is a ratio of about 2.4, far short of the generally accepted rule of thumb guideline of a minimum ratio of 10 at all audible frequencies. With the consequences of that shortfall being particularly compounded by the wide variation of the preamp’s output impedance over the frequency range.

Also, it is still quite possible that if the cables to the subs are particularly long and/or if they have high capacitance per unit length their capacitance could be affecting the upper treble content of the signals received by the BAT power amp.

Regarding ...

Repeter 12-30-2017
Cabling from pre to power amp would be Nordost. Could these long (2 meter) flat silver (Ag) play into flat/dull performance at low volume? FYI, I used them to drive my Sophia 3s and Geoff Poor (BAT) recommended the massively improved Audioquest CV-8s. So.. Could driving my power amp with these be a weakness?

... I’m not sure I follow this. I thought the CV-8 is a speaker cable. And what specific model are the Nordost interconnects?

Regards,
-- Al

P.S: It occurs to me that the 100K input impedance of the BAT amp probably means 50K for each of the two signals in the balanced signal pair, and the measured 14K balanced output impedance of the preamp at 20 Hz (assuming the Six-Pak is not installed) probably means 7K for each signal. So when the subs are connected the one signal in the balanced signal pair that is connected to both the sub and the power amp would be loaded by 50K in parallel with 50K, which is 25K. 25K/7K is a ratio of about 3.6, still not good! Also, there would be a significant imbalance between the impedances of the two signals in the balanced signal pair, given the high output impedance of the preamp, which is also not good.

All of this assumes, though, that the balanced and unbalanced outputs of the preamp are not driven by separate and independent output stages. That is the case with most preamps which provide both balanced and unbalanced outputs, but I don’t know for a fact whether or not it is the case here.

Regards,
-- Al

Czarivey, 
To answer your question of "name me one musician who likes Wilson speakers, Peter Poltun of the Vienna, Vienna Philharmonic Orchestra, violinist Wilfried Hedenborg and numerous others. Don't comment on things you know nothing about. Wilson makes great speakers: I owned them for many years. And I play guitar. Not great, but I can play it, and piano (worse, but still, I know what it sounds like). Don't be a wanker. 
Now back to the original poster: 
What's the amp? What are the cables? What is your room size and have you treated it acoustically or tested the room acoustics? I assume your wife plays her instrument in your home, so she has an idea of the acoustics, but you haven't stated this, so I don't want to go on assumptions. If your amp has a low impedance output - as I understand it - there could be an electrical mismatch. 100K output is a good match between the preamp and the amp, especially if the preamplifier is tubed.