Poll: What's your KT150 bias set to per tube (ma?)

@oldhvymec - If you could limit the bass duty on the valves, I think you’d really be surprised.

An unexpected added surprise was the lower register midrange and upper bass range that just came through biasing up on the KT150s. I usually run custom 12" Scanspeak active subs for 50hz below in my setup. Now after having biased up the main mono tube amps, immediately had to turn the sub down, off, almost don’t need it. oldhvymec, i know you know the "sound", its reminiscent tone and sound closer to running two V12R mono blocks, yet I’m running only (4) KT150s instead of (12 or 24) EL34s across two mono V12Rs. Using Mullard Blackburn mid 60s dual-triode 12AU7, 12AT7/CV4024s in front of the KT150s to shape tone. Also worth noting, Mundorf Silver-Gold EVO coupling caps (same as my former Cary amps had) now in my current KT150 mono amps. This too brought the KT150s to another level with nice tone and texture, probably closer to what you might know from a V12R with these same caps paired in Cary amps and GL KT88s, a tad more transparent than EL34s.

Interesting, I haven’t ran 120 or 150 so I just don’t know. BUT it is good to know.. I’ve used the valves I use so long and the supplies I have are all about 6V6, 6L6, El34, 6550, KT88, KT90. I doubt I would change.. BUT I should never say never.. Things change, that’s the only thing for sure..

Just like a lot of folks like running single ended. I NEVER have, I’ve had a few SET, 300B la te da.. Every time I go back to A/B or UL.. Just my speakers and my ears.. Small planars and fast tubes work for me.. Bloated or slurry along valve units just turn me OFF. Not much of a Flea Watt guy..

Sounds like you have a GREAT setup.. I gotta get out more..

I have been looking at a pair of late model Cary SE though.. We’ll see
I sure do like my V12R NOW. It had changed a LOT from when I got it.
The biggest change for me was the signal caps.. I went to silver Jensens, THAT change it from a tubie sound to laser imaging, pinpoint clarity.. I’m sure it would preform well doing bass with a few of the speakers I own.. That is a serious amp. NOW, Before. Nice!, Never a serious contender against my MC240s.. Sure is now....

Still HEAT.. is a killer for me.. I can't take the heat from them in the summer months.. BUT I did lower the heat index a bit.. 6V6s and new filter caps with a little tweak.. I can make it to the end of June.. and start back up mid Oct.

Regards

All that blabbing and still didn't say..

BIAS differently makes a difference.. :-) Things are not set in stone from valve to valve either. Some brands of valves act different too..

Seems so. Just heard from my amp designer/builder. My KT150 amps sounded a little dry at 40ma per tube. 50ma showing real hope. Op manual shows 40-60 for my model. Asked if I could go up to 55 or 60ma. Designer shared "60ma is still well below the maximum rating of the KT150 tube". Still well within the safe zone it seems. An easy and fun experiment.

I would be interested to know if the amp designer would bless the KT170 tube as the better tube overall for that model and what xxma would be appropriate for that tube.😬

Good to know 60ma is still well below for the KT150. At 50ma my sound tightens up, liquid, speed and power with remarkable naturalness and finesse in the recreation of tonal and harmonic information is the great strength of these mono amps. I have the Brimar CV4003 and Mullard 6201 in my amps. I’m sure my field coil drivers voltage settings play a big part of the sweet sounds too.