Questions about Ethernet Cabling


PLEASE READ: This is not a thread about the merits or demerits of audiophile-grade ethernet cables, or any cable for that matter. If you don’t believe in spending extra on expensive cables, I respect your opinion but please don’t turn this into a point of contention.

So before I ask my questions, let me describe how internet connectivity is setup in my house:

- [Home office/study] The modem (AT&T), router (Google Nest/Mesh), and switch ($25 TP-link basic switch) are located in the home office/study. I also have a second system in this room as well as other stuff connected through the switch. In other words, I can’t move the switch to another room.

- [Media room] The main audio system is located in the media room which is in the diagonally opposite side of the house (single story). This room has the ENO ethernet filter connected to the Innuous Zenith MK3 streamer, and so on.

[Long ethernet cable] A very long run of ethernet cable (CAT 6/over 100 foot) runs from the [Home office/study] router and terminates into the [Media room] ethernet jack/wall plate. This was done by the builder and it runs through the attic.

- [Media room] From the [Media room] ethernet wall plate, I then use another 6 foot ethernet cable (also CAT 6) that goes into an ENO filter and then on to the Innuos Zenith MK3 streamer.

 

So here are my questions:

1. Is it worth upgrading only the so-called last-mile ethernet cable, i.e. the one between the [Media room] ethernet wall plate and Eno filter while I continue using the long CAT 6 cable [Study >> Media room]? It is going to be difficult, if not impossible, to replace the long-run CAT 6 cable as it goes through the attic where several spots are not reachable without tearing down some sheetrock.

2. Is it worth adding a second audiophile-grade switch (e.g. uptone) in the media room while leaving the one in the study as is? Or is it better to upgrade the switch in the study first and place the cheaper switch in the media room? Or do I need to replace both switches (not prefered as it adds to the cost)?

 

128x128arafiq

The. more I read about this, and the more I learn from folks like @lalitk and @antigrunge2 the more I think that things happening before the streamer are perhaps even more important than the streamer itself. Better switches, clocks, wires ... I’m almost beginning to wonder if one is better off buying less costly streamers and investing more money in fiber optics switches, clocks, and USB relockers.

I won’t be surprised if we start seeing single-box solutions in the future -- including switches, ethernet or fiber input, clocks, better LPS, and USB relockers all in the same box. Not everyone appreciates a jumble of boxes, LPS and wires everywhere :)

 

I have been asking this question ad nauseam so I understand if I get shouted down. What is the purpose of the high end servers, wires, etc..? My understanding it to curb the analog noise getting into the DAC. What if the DAC is served the music by fibre cable which cannot carry the analog noise? Ideally with something like a Lumin X1 DAC with a direct fibre connection to stream from a network switch with an SFP. Why would one care about what was behind the fibre cable (in front is the DAC)?

@yyzsantabarbara

To reiterate a bit.

I had a Lumin T2 and ungraded to a Lumin X1 (found used on Agon…..who would have thought?) and perhaps because of purchase bias or maybe for real I thought the sound ticked up a bit.

Then I upgraded the PSU cable to the X1. That was a definite improvement. Golly!

Next I put in the EitherREGEN (and AfterDark goodies clock & PSU ....prices in Hong Kong dollars ) making use of the optical into the X1 (the non optical sound has a different flavor that’s great too, really) and cleaning/filtering the signal was the most significant positive change change ever. BAM

I’ll never know but had I cleaned up the ethernet signal into the streamer/DAC I’m not sure that I would have changed streamers.

A lot of info here too in another discussion.

 

 

 

 

Hello.....connect a PC to the Ethernet and get a free Speed Test App from your ISP or other. Anything near 20mbps should do it.