Tube or Trasistor

I would say. Start studying acoustics at the internet. Can you place a picture of your livingroom? It's a waste of money to buy more equipment if the acoustical conditions are not oke. Even than it will stay difficult to advise you.

On vacuum tubes—then and now…

I returned from draft duty in early ’54, and from that time on I’ve been absorbed with high fidelity audio. Of course, the early years meant embracing vacuum tubes. Transistors weren’t ready for prime time, so tubes were the only option. And I soon learned that tube technology was far from perfect. Tubes suffered high incidence of failure, and their abundant heat cooked adjacent parts. But those faults could become my gain if I learned radio/TV repair, so I built (from kits) a tube tester, audio oscillator, oscilloscope, bought a multimeter, and began my career in the industry.

Tubes reflect their Neo-Victorian vintage (1904); they’re just not high precision parts. Why not? Well, to start, the tube manufacturers identify vacuum tube operating parameters only by listing “average” or “typical” characteristics. They never specify tubes by providing precise min./max. limits, as with solid-state devices, so tubes lack uniformity from their git-go. That’s why tubes of the same type often differ so widely. Further, all tubes exhibit random long term drift when put into service; plate current falls and grid bias shifts. These changes reflect a persistent degradation that begins at initial turn-on and ultimately ends in cathode depletion failure—barring other common modes of premature demise. (E.g.: open filaments, vacuum leaks, gassing, microphonics, atypical distortion, excessive hum/noise). So vacuum tubes are not a wise choice when stable circuit performance is a serious design goal. Regardless, for some 70 years tubes were all that we had. Circuit design creativity got pretty stale toward the end of that era, largely because tubes were just too big (and too inefficient) to use more than the functional minimum. But innovation revived with the debut of complementary solid state technology in the mid-to-latter ’70s.

Early angst: In 1963 I bought a hi-end Fisher FM-200B tuner, one of the top signal seekers of the day, but its RF/IF stages exhibited incessant drift due to tube aging. I had to perform tedious realignments annually. And my 1962 Marantz 8B stereo power amplifier needed quarterly output stage re-biasing to hold IM distortion inside 0.5%, plus I had to install four new EL34s every two years. Indeed, I got so anxious to dump vacuum tubes that I built my own solid state power amps in the mid-’70s, as soon as PNP silicon power transistors became affordable. Free at last!

Vacuum tube commerce has collapsed in the 40+ year lapse since my escape. All of the principal domestic, British, Dutch, and German producers are now either defunct (like Tung-Sol Electric, my employer from ’57 - ’60), or they’ve long since ceased making tubes. The entire world market for (receiving-type) tubes is now confined to a small coterie of audio and guitar buffs, and served only by obscure Russian and Chinese suppliers with no previous market recognition. (There are other minor sources in former Soviet bloc countries.) The quality and reliability of the tubes made by those arcane foreign suppliers is a subject worthy of concern. And those sources will persist only as long as there’s viable demand, so the outlook for assured access to replacement stock seems dicey. Further, this situation prevails at a time when every instrumented means of evaluating audio quality validates the measurable superiority of modern solid state design. Tube boosters reply that “my ears are more accurate than your instruments”, but their faith is mired in groupthink. There’s no credible A/B/X aural evidence to support the “tubes sound better” cult. Tubes were marching to the casket 40 years ago. Don’t consort with zombies.

^ and yet EVERY great guitarist today,from Jazz Standards to Metal continue to play through TUBES!!!
SRV in concert,TUBES...
Carlos Santanna,TUBES...
Clapton,TUBES...
Peter Frampton TUBES...
BB King-Buddy Guy and Albert King,TUBES...I could go on and on...
Bet you can't name 3 great guitarists and their Solid State stacks...

As duly noted: "The entire world market for (receiving-type) tubes is now confined to a small coterie of audio and guitar buffs..."

Guitar amplifiers are often (intentionally) over-driven into clipping overload, where their predominant even order harmonic distortion is deemed a desirable aural characteristic. Producing this even-order harmonic distortion is the intended objective, and it's easily accomplished with a vacuum tube output stage circuit.

vtv, Yes solid state has many benefits over tubes but the amp or preamp with the lowest distortion does not always sound best.  Some people prefer the sound of amps or preamps that include tubes in their circuits.  So why buy a more accurate solid state device if you enjoy listening to a tubed device more?  Knowing that your system has lower distortion and that transistors are less likely to go bad doesn't seem like adequate compensation to me.

Recordings come nowhere near replicating live music.  So even if you could put together a system that introduced very little distortion, you would still be a long way from the sound heard in the studio.  Every format and system sounds different, so it's a matter of choosing which variation on the original event you prefer.