what is dynamic headroom?

Don't worry about the dynamic head room spec - a lot of ss amps have a value less than 1.0, including the big ticket ones. This value can be relatively meaningless if the duration of the extra power is not specified.

As far as damping factor is concerned, a ratio of speaker impedance to total output impedance greater than 10 will adequately control most cone drivers. The speaker cable impedance has to be added to the amp output impedance for the total impedance. An amp with a low DF and long, capacitive speaker cables is the only reason to look at the DF if it's less than 50 or so, IMO.

Alone, neither one of these specs will tell you very much about how the amp will sound in your system and room.

Dynamic hr is really just the ability of an amp to put out more power than its rating would suggest. For example, an amp rated at 100w per channel that can put out 200w for short durations ( a few milliseconds) has 3db of headroom. There are various reasons for amps to have different hr values. Form instance, some amps are rated very conservatively and this will account for high hr values. Other amps have well regulated power supplies which means they will probably have low values of hr. On the other hand, some amps' power supplies are loosely regulated and will appear to have more hr.

Power is logrythmic in nature and one or two db may not mean much (and may not even be audible on music).

I would be more concerned with an amps' ability to be able to deliver more power into low impedance loads.

Damping factor is just a ratio of the amps' output impedance to the speakers nominal impedance. For example, an amp with an output impedance of .1 ohm and a speaker with an impedance of 8 ohms has a damping factor of 80 (8 divided by .1). Damping factor relates to an amps' ability to control a speaker's cone movement. Higher is better, but anything above 80 or so is questionable whether it improves anything.
Jim

Zaikesman,

Good info in your post borne out of experience I note & point well taken. Thanks for sharing the same.

BTW, I wrote some basics on D.F. without meaning to write how much is high enough (as Fishcall posed a basic question); rather, pointed out that d.f. is freq. dependent & that if the B&K can hold df=100 across the band, it would be doing very nicely. Why 100? 'cuz Fishcall read that off his amp's spec sheet so I stuck with that #. Is it enough for his room, his music, his volume level? Don't know!

How much df is enough is very debatable & many view points exist. The Gamut website has a paper saying that df=25 is more than enough. This # falls in your 10-100 range but it is rather subjective whether df=25 will suffice. What I find when the df is on the lower side that such amps cannot be used in any system that one pleases i.e. the amp & speaker have to be carefully matched. I consider this to be a negative aspect as the user's favourite speaker might be precluded from the list. Others might not feel this way at all. However, I agree with your view point that too much of df can be detrimental. It seems easier to pick out the lower limit (where bass is wooly) & the upper limit (where the bass is dry) but I'm not sure that 10-100 is that range as I've not done any tests myself to quantify this range. I agree that each one of us needs to choose the level of DF & its impact on sound in their resp. system.

Aleph 5 50 nominal is the damping factor
Aleph 3 100 nominal is the damping factor
SF Power 2 100 damping factor
ML 33 greater than 800 @ 20 hz, this is a very good figure to look at as this is typically where you want the greatest control of the drivers, in the low bass region. The Aleph products because they don't over control drivers are considered more tube like. Tubes also don't control drivers as well as SS.
This didn't answer your question about DH but should give a reference on Damping Factor.

wow! thanks for all the great responses. i love this site! the B&K's dampening factor is 100 at 50Hz. that's all the info that the specs give, but it looks like i do not need to worry with the specs and see how she sounds.....
thanks,
fISHCALL