condenser versus direct coupled?

A "condenser" is an old name for a capacitor. Placing the cap in series with the signal will help prevent DC leakage from a source component or preamp from being fed into the power amp. It is strictly a "safety" feature and will only detract from the sonics. I make the last comment based on the assumption that Hitachi wasn't using the highest grade capacitors in their components. The "direct coupled" output bypasses the cap, which could result in better sonics ( PROBABLY ) but could also put the system at risk of damage if using older components that could be defective.

Try it both ways and see what you get. Sean
>

Sean raises a good issue, that is speaker protection from DC. Make sure the drivers in you speakers are replaceable before you decide to use an amp that passes DC. Its not a huge deal if you take out a couple of drivers due to DC unless you can't replace them!

A direct coupled preamp is not going to blow out any speakers unless the power amp is also direct coupled. Chances are that the preamp output goes into an input capacitor of the power amp, so you will still be ac coupled regardless of which preamp output you use. I would go with direct...who needs two capacitors in series?

DC won't burn up speakers any faster than AC, but you would not get the audible warning that something bad was happening. However, direct coupled amps that I am familiar with include circuitry to detect this fault condition, and turn themselves off. Some AC coupled amps (particularly pro sound amps that are often driven very hard) also include protective circitry.

And then there are speaker fuses.

DC absolutely WILL burn up your speakers faster than AC, especially if of the same peak voltage level. That is because DC has a much higher RMS level than the AC waveform generates.

As the AC waveform vacillates from positive to negative and varies intensity*, the DC signal remains consistent in amplitude. Unless the DC has a high level of ripple, the peak power is the same as the average power. With AC, the peak is measureably higher than the average. This means that the heating power of DC voltage is FAR greater than that of AC. Due to this factor, DC tends to melt voice coils and / or the glue that secures the voice coil to the coil former much faster and at lower levels. Sean
>

* With AC, the intensity varies due to the "hill and valley" shape of the sine wave. Not only is the voltage varying as it climbs up and down those "hills", the duration or "thickness" of the peaks and valleys vary too. On the other hand, DC is pretty much a steady state signal that remains consistent. If you took the same peak amplitude of both signals, the DC would look like a straight line running across the peaks of the AC "hills". If you look at the average power that the DC signal maintains compared to the areas that drop below that flat line at the peaks of the hills, AC is FAR less "potent". The reason that we don't use it for our power grid is that it doesn't fare very well when travelling long distances. As such, we generate AC to send the signal over a long distance and then convert to DC for it's greater work-load capacity.

Sean...You really ought to be more specific than the frightening "FAR greater" when describing the damage potential of DC vs AC. Actually, as I think you must know perfectly well, the rms voltage of a sinusoidal waveform (its heating power) is 7/10 that of its peak voltage, which is presumably what you are assuming for DC from a faulty amp. Furthermore, if the amp goes into oscillation, which is the most likely failure mode, the output will be a square wave, (instead of a sine wave) which has exactly the same power as DC. Both levels could cause damage, and the difference in time required for damage to occur would NOT be great. I think that, because there is no loud audible indication of a problem with DC, amplifiers that are DC coupled are more likely to include protective circuitry. (Mine do).

Oh, and by the way, DC transmits over long distances very efficiently. Better than AC. A lot of research work was done on that technology here in Pittsfield Mass by the General Electric Transformer business. (Alas, GE quit the large power Transformer business). The problem with DC is that there is no easy way to step voltage up and down. With either AC or DC long distance transmission calls for voltage of several hundred thousand volts. You can't have that going into your house!