Help With 60Hz Hum PLEASE


Greetings,

I am having some issues with noise coming through my speakers at low volume. The noise sounds like a 60hz cycle hum, and can be heard clearly when the volume is all the way down. I have tried several things to quiet down this noise, but nothing has worked so far.

Before I give details of action items I have tried, let me inform you of the components I am running.

My system consist of:

·     AV PRE/PRO MARANTZ 8801

·     AMP ADCOM GFA-7805

·     SONY 300 DISC CD CHANGER

·     SPEAKERS B&W CDM9NT/CDM CNT/CDM1NT

·     SUB VELODYNE SPL1000 SERIES II (NOT HOOKED UP AT THIS TIME)

·     USING XLR INTERCONNECTS BETWEEN PRE-AMP AND AMP (MONO PRICE)

·     DEDICATED OUTLET CONNECTED TO 20AMP CIRCUIT BREAKER

·     FURMAN POWER CONDITIONER (EVERYTHING PLUGS INTO THIS)

·     I SEGREGATE OUT THE AC POWER LINES FROM THE SIGNAL AND SPEAKER CABLES


So this is what I have done to check the system so far.

1.   First off I separated all of the components power sources, plugging each component into its own outlet with the amp plugged into the dedicated outlet. (NO CHANGE, NOISE PRESENT)

2.   Unplugged any no essential item leaving just the pre-amp and amp plugged in (NO CHANGE, NOISE PRESENT)

3.   Removed the amp from the system, plugged in single source and speaker set (NOISE IS COMPLETELY GONE!!!)

a.   FOR ABOVE TEST I USED MY IPHONE WITH A SET OF RCA INTERCONNECTS STRAIGHT TO THE AMP.

                                              i.   I really suspected the amp at first because about a year ago I had the unit repaired for a standby condition. The repair center I used also repaired the CENTER CHANNEL BOARD while they had the unit. I noticed that the center channel has almost no noise coming through, but after the previous findings I decided this might be a symptom not the cause of the noise.

4.   Hooked back up system and tested (CRAP, THE NOISE IS BACK)

5.   Unplugged all of the XLR interconnects from pre-amp side (NOISE IS GONE, YEAH!)

6.   Plugged in one interconnect into pre-amp (noise comes through that channel)

7.   Switched between XLR and UNBALANCED (THE UNBALANCED CONNECTION WAS A BIT WORSE)


My conclusion is that something is happening between my pre-amp and amp that is allowing this 60hz signal though. I am wondering if it could be the interconnects themselves because I am not using a high quality interconnect. All I am using is Mono Price XLR cables. Although, why would there be no noise when the cable is plugged into the amp and not the pre-amp? Might the Marantz 8801 be the culprit due to the fact that when I plug in the cable into the pre-amp is when the noise comes through? Or maybe my first instinct was correct in that the amp is the problem?

Any help figuring this out is appreciated.

Thank You Kindly,

Joe

jo3533
Did you try using RCA connections from 8801 to 7805?
The 7805 has very low input impedance on Xlr.

2.   Unplugged any non essential item leaving just the pre-amp and amp plugged in (NO CHANGE, NOISE PRESENT)

To be clear, you had nothing connected to any of the line inputs on the Marantz A/V preamp? (All the input jacks were empty of Interconnect cables?) Volume control set to minimum.

The only interconnects connections were from the outputs of the Marantz to the Adcom power amp. Is that correct? 


Do you have Cable TV, or a Dish, connected to the MARANTZ 8801? 

If you have a cable TV connection to your audio system, it is probably this. I've had hum problems with my phono preamp that was corrected by re-orienting the equipment to a different location.