2. amps-preamps
  3. 124255-73035

Dual Differential / Balanced?

Hey all I’ve got that itch to upgrade power amps, and was wondering how valid the dual differential aka "balanced" monoblock or dual mono design is in terms of increasing fidelity compared to a conventional SE amp. note my preamp is also fully balanced

how much noise is avoided by using a fully balanced system?

right now I use 2 haflers horizontally biamping NHT 3.3. using mogami gold XLR
p4000 200wpc mids/highs p7000 350wpc lows

from what I’ve read it only matters if both the preamp and power amp are both truly balanced

I have a nice Integra Research RDC 7.1 fully balanced pre/pro, it was a collab with BAT, I would go for the matching RDA "BAT" amp but its pretty much unobtanium

So far I’ve looked at classe ca200/201, older threshholds, older ksa krell, as fully balanced monoblocks/ dual mono stereo

I was also told to look at ATI amps, they look very impressive but expensive

I’m looking to spend 1500-2500 preferably used products, I dont have an issue with SE amps I just want to exploit the fact my pre is fully balanced, and perhaps get better sound. If anyone has recommendations for awesome dual differential power amps. the NHT 3.3 are power hungry so at least 150wpc, class A/AB

I’ve also come across the emotiva XPA-1 monoblock, I can get a good deal on one of them I wonder if its worth picking this up and praying for a lone one to come on classifieds on ebay- note this is the older model in the silver chassis 500wpc 8ohm / 1000 4ohm

for context prior to the realization that I should use a fully balanced system I was looking at brystons and mccormack amps.. thanks
nyhifihead
almarg's avatar
Ag insider logo xs@2x
almarg
9,670 posts
 
Charles & Kijanki, see Ralph’s first post dated 3-22-2013 in this thread for a summary of what is necessary to make a balanced line-level interface insensitive to cable differences. And also for what I consider to be a compelling proof Ralph offers for his contention.

But also note a question I posed a few posts later in that thread, and the answer Ralph provided:
Almarg 3-27-2013
... to eliminate interconnect cable differences is it necessary that the component output actually BE driving a low load impedance (2000 ohms or less, to use your figure), or is it just necessary that it be CAPABLE of doing that?

Atmasphere 3-27-2013
You touched on an interesting point about the load vs the capability to drive that load. I have found that the capacity to drive the load plays a huge role, about 80% but for that last bit of cable artifact to go away the load must be there as well. Flipping the coin over- if the capacity to drive the load is absent, then its moot and there will be cable colorations.
I see that the MA-1 amplifier which Charles mentioned has a specified balanced input impedance of 200K. I’d imagine that one reason Ralph would have chosen to not provide a very low input impedance, such as the 600 ohm standard he refers to, is that most preamps made by other manufacturers would not be able to drive such a load with good results.

Best regards,
-- Al

charles1dad's avatar
charles1dad
10,250 posts
 
Thank Al, 
So very specific requirements are necessary in order for Ralph's point to be valid,  I appreciate the clarification. This would explain the findings of my friend's Atma-Spheres and his various balanced cables. 
Charles, 
bdp24's avatar
bdp24
9,821 posts
 
I don't know about advantages (if any) provided by a true differential balanced circuit, but EAR-Yoshino designer Tim de Paravacini (who does a lot of work in the pro recording field) chooses to use single-ended circuits, with balanced inputs and outputs provided by a transformer.
philipwu
214 posts
 
"Checkout VAC SigMKIIa SE and above or Atmasphere MP-1 if looking for transformer coupled preamps " by knghifi

dear Ralph, 
is your preamps transformer coupled? (or is it in the signal path or stages?) 
btw, may i ask if your preamps are designed with absolute no local, no global feedback in power supply & audio circuit? if the info is something proprietary to you, then just ignore the questions. Thanks & regards, 
-phil
swampwalker's avatar
swampwalker
5,138 posts
 
As is usually the case in audio, how good the results are depends less on the design approach that is chosen, and more on how well the chosen approach is implemented.

Yes, yes, a thousand times yes!  I nominate this as verse 1 in the Audiophile's gospel, to be said aloud, immediately upon arising in the morning, and before retiring at night!  J/K.  Not really... ;-)

More to discover