2. cables
  3. 1335297906

High Fidelity Cables CT-1designed by Rick Schultz

In December 2011,I wrote that High Fidelity cables led by cable designer Rick Schultz was putting together a new cable.The cable came to market as CT-1.The CT-1 has FINALLY made it into my system!I had obtained a version of the prototype that Rick had been working on.It blew my previous reference Genesis by Virtual Dynamics.I thought I had finally found my end with this cable.This prototype delivered to my ears "Nirvana".Could I be at the end of my quest for the ultimate sound?
No. I received two pairs of CT-1 to replace my prototypes.They went into the system this past Friday.Unable to dedicate time until Sunday listening,I stole a few moments,ducking away from company with anticipation.My guest could tell even with the music set for"ambiance"something was intriguing and I was in for a treat!
The experience:
First off,CT-1 was very user friendly.Installation was simple;the cable is very nice and light.The female RCA fit beautifully unlike any I had found in other cable.It was secure and reliable.It seemed much thought was dedicated to developing a designer fit to an aesthetically stunning RCA connector.Install entailed a few wiggles to ensure what seemed like a compression fit on my RCA.
It was 2-3 hrs. for the 1st step of break in to be complete.At that point I had something different!Today,although they only have 10-12 hrs. on them,I can`t put into words how much my system has transformed.Believe me,I loved my prototypes.However....there is simply no comparision.
The clarity and sound is so natural.
The soundstage is like nothing I ever heard.Resoulution is breathtaking and inner detail is simply hard to believe possible.
The sound has transended and now it simply does not seem as thought I have speakers.
My system is musicians playing music.
I am told with time they will improve and I trust that as it was revealed with the prototypes.I wanted to share my thoughts with you that now.
Unequivocally,a testament to High Fidelity,as the name declares.
High Fidelity Cables for me,the last word on it,after 12 hours!
Truly Amazing

Al
alpass
ddraudt's avatar
ddraudt
609 posts
 
Hey Calvin, Cool that you may try the 6 Hemi!
I'd be interested in your thoughts on the difference between 
the 6 and the 6 hemi.

My system is so addicting and so enthralling that it is very hard to get anything else done if it is playing. Ricks inventions play a major part it my sound. Like Norm, over 50% of the cost of my system is in High Fidelity Cables. I'm so happy with that choice that I hope to up that percentage 
by a lot with my efforts to get Pro Speaker Cable.

Cheers D
ddraudt's avatar
ddraudt
609 posts
 
Keith, you are way off topic my friend.
I can't imagine anyone on this thread wanting to read what you have written.
May I suggest that, if you think someone is being abusive, you click on "report this post" so a site monitor can take a look at it.
I mean no offense but I will ask that they remove your last post to eliminate another negative direction on this thread.
Happy thoughts!!
Hope you and your system are doing well!
Cheers D
PS I have very strong opinions and judgments about things which I try to balance with education and understanding. Flawed human.

philipwu
214 posts
 
hi,
has anyone tried using digi-multimeter to measure Rick's powercord? 
what i did was just simply measuring the impedance of the Earth, Hot & Neutral conductors on my CT-1 powercord.
the result i get on the Hot conductor wire measures about 5ohm or less, the Neutral is around 10kOhm, and the Earth conductor is a staggering 12Mohm. the test was repeated 3 times and hold for about a minute for the results to settle so to get magnetic effect to "calm down".  i also measured a typical lampcord , all three conductors in Hot, Neutral & Earth are of the same value about less than 1ohm. 
Cerious GE power cable also have a "slow" conductor on the Neutral side, is there anyone would like to comment on the resistance (impedance) that's on HFC power cable?  what about the impedance of the upper tier of Rick's power cable? anyone?
-philip
ddraudt's avatar
ddraudt
609 posts
 
Hello philipwu,  A lot has been brought up about Magnetic conduction not working the same as electrical conduction on this thread in the past 5 years. We unfortunately cannot apply electrical logic to magnetic conduction. You are measuring electrical resistance using the batteries in your meter. You are testing magnetic conducting materials with  electrical  conducting test equipment which is even further afield than testing AC current with a DC meter.
Not to worry brother, many have had a difficult time moving to a radically new medium. Except for those who have tried a full loom.
Some have not been able to make the adjustment AT All! and have left thinking we are all crazy. like the flat earthers did some time back.
Hang in there man!
Cheers D
jay23
210 posts
 
hifial,

Thanks for all of the information you've procured! Especially about the 10 amp "limit".

In regards to the Helix Waveguides, I understand the internals and construction are fully different. However, even if you look at the module in the video for the CT-1 Ultimate Reference Helix Power Cable (http://www.highfidelitycables.com/products/power/ct1urh/), you will see it is designated as the "CT-1 Ultimate Reference".

That is why I was interested in what the modules in the Hemisphere are designated. The different module types likely indicate different strengths or quality levels of magnets. Given HFC states, "The MC-6 hemisphere may not represent the most exotic product built by High Fidelity Cables for power conditioning," gave me more interest about its modules' designation.
 


More to discover