2. analog
  3. 125140-118

What is Technics thinking?

Lots has been said, both pro and con, about the new Technics turntable.  Description here -

http://www.sl1200gae.info/about

Some are excited about the potential, given the upgrades since their last production table/arm, the venerable SL-12XX series.  Others see it simply as an excuse to raise the price significantly of the 1200s.

In my view they shot themselves in the foot.  They copied the model number of their best selling table (I can only imagine in the hope the familiarity will carry over) and also ended up with a very similar appearance.  Given the information on all the upgrades over their prior model, the similarities make it appear like something less than what it might be.

Technics had a room at THE Show Newport and that was my first chance to see a SL-1200GAE.  The fit and finish appeared to be very good but it did look like a "polished up" SL-12XX.  I ask the Technics rep why they didn't do more to distinguish this as a new model, given their efforts with engineer upgrades.  He said he could understand my question but then really didn't offer a reasonable explanation.  After describing all the components which had been redesigned/upgraded from the prior model he offered a demo.  However the room was crowded and the remainder of the system was completely unfamiliar, so no fair impression could be made.

I believe it should have had a more unique model designation and more might have been done to the physical package so it didn't look so much like the prior model.

pryso
johnnyb53
3,510 posts
 
While the SL does allow limited azimuth adjustment, spinning the P-mount head shell is a time consuming hit or miss affair.

I think you mean 1/2" universal headshell. P-mount is a non-adjustable plug-in with no lead wires to attach. The Jelco HS-20, HS-25, and HS-30 universal 1/2" headshells all include azimuth adjustment. 

The HS-20 is available in the US as the Sumiko HS12 headshell; the HS-25 is available as the LP Gear ZuPreme. The ZuPreme is the better deal---$54.95 with built-in finger lift vs. $90 for the Sumiko with a fussy finger lift that requires threading the cartridge mounting bolts through the cartidge, headshell, and finger lift.

Also, I check for and adjust for azimuth by setting a small bubble level on the top of the headshell (with stylus guard in place), loosening the hex set screw to rotate the headshell until the bubble indicates it's level, and then tightening it again. 
pryso OP
1,946 posts
 
m-db, ah yes, I'd forgotten about the WTTA.  And I owned one, but that was many years ago and thus my excuse.  Still, I can't think of any others.

Also, as noted, I don't believe the standard SL headshell is a P-mount.  At least the one I saw at THE Show Newport in the Technics room had a standard 1/2" universal headshell.

johnnyb53
3,510 posts
 
Also, as noted, I don't believe the standard SL headshell is a P-mount. At least the one I saw at THE Show Newport in the Technics room had a standard 1/2" universal headshell.
No one on this thread said that the standard Technics SL12x0 series headshell is a P-mount. Did you see such a statement somewhere else?  It's always been the universal 1/2" headshell going back to its introduction in 1972. 
totem395
390 posts
 
johnny
Also, I check for and adjust for azimuth by setting a small bubble level on the top of the headshell
I use a bubble also but find a pencil lead if able to be kept in place
my go to choice.
m-db's avatar
m-db
997 posts
 
pryso, P-mount, Universal, I assumed they were the same. Thanks for that.

totem, for many years I used a level followed by carefully listening to a test record for my azimuth adjustment. Then I borrowed a Fozgometer and realized a greater accuracy and an improvement in staging.  
To complicate things further the Well Tempered Classic has a slightly concave plater. 

More to discover