New Mag-Lev Turntable

I would think that anything that separates the platter and tone arm, allowing either to be suspended independently from the other would be a problem.

you know raymonda

There is this subtle but important difference between "I think" and "I would think" :^)

If a person says "I think"., it is a straightforward statement about their thoughts on the matter. However "I would think" means that the person would probably argue for whatever is being discussed, if they were asked the question or put to the test.

So for this reason just one question really - is your opinion based on theory, or personal experience ?

if it is the later - personal experience, always looking to learn.

as we know...
Air bearing tonearm spindles are, "suspended", "levitated", and ride on a film of air. Some are partnered with direct coupled turntable platters. while with others, their platters are also levitated. This has been happening since well the 80’s anyway, and is still happening today.

****************
Geoffkait
How do you think this Mag lev table platter stays aligned ?

I think it has to do with same pole repulsion for the main part of the platter and around the edges there is a circular opposite pole pattern. . What do I know. You are the NASA guy right ? What do you think ?

"Geoffkait, How do you think this Mag lev table platter stays aligned ? I think it has to do with same pole repulsion for the main part of the platter and around the edges there is a circular opposite pole pattern. . What do I know. You are the NASA guy right ? What do you think ?"

I don't know. How much do you think the platter weighs?

geoff

I think that air bearing tone arms are considered rigid, and they fall within the same tolerances as standard bearings. I'm not so sure that this magnetic platter design does. From the video you can clearly see a large variance where the platter deviates from flat. Now, whether that is from loose tolerances when manufacturing the platter or suspension effect is unknown.
 
Also, it would be interesting to knock the side of the plinth and see what happens to the platter, as well as, what happens to the whole table while playing an album.

How much do you think the platter weighs?

well thinking out loud this morning. It’s a "look Mom no hands" free floating design, so permanent magnets must be embedded in the platter in some pattern. The plinth portion is using electro magnetic forces. So one idea is; I am visualizing a repulsive force on the inner part of the platter, and some kind of metal ring embedded in the platter closer to the rim. This metal ring provides attraction to the plinth’s forces keeping the platter aligned. We don’t know what kind or amount of electro magnetic force is involved, but the platter floats very high. With cartridge shielding considerations, this makes me think the platter is therefore not very heavy. Without knowing what the actual materials are that the platter is made of, I am guessing, so let’s say a few pounds.

From the video you can clearly see a large variance where the platter deviates from flat. Now, whether that is from loose tolerances when manufacturing the platter or suspension effect is unknown.

I learned from personal experience, never to trust videos and pictures. Especially if you are buying a used boat 8^0.
Damn, when you go to see them, they always look worse than the pictures and videos.

Tolerances is IMO what the audiophile should focus on, when buying a packaged turntable setup (table, tonearm, cartridge). Tolerances are what separate the men from the boys. What should separate a 4 figure turntable package from a 5 figure one.

Example.
So a friend buys a 4 figure turntable package. Table, tonearm and cartridge. He levels the plinth feet to the point where the platter is level in the general area where the tonearm will travel. He then checks the level of the tonearm armboard which is fixed to the plinth. It is not on the same plane as his platter. His tonearm (the one that came with the package) does not have a self leveling system. What’s he going to do ? What happens when he goes to check the other half of the platter ? Is it on the same plane as the side the tonearm rides on ?
I think the person buying this Mag Lev turntable setup is not even thinking of tolerances. He or she is thinking this is so cool, I have to have one. In the end it is always the cartridge and some records that are the victims in a bad setup /design. The website says they have some folks using the product and providing input. Hopefully someone from the project team will have a look at the cartridge after XXX hours, to see what is really going on. To find out the truth. And this reminds me. if someone is having a cartridge re-tipped don’t forget to ask your re-tipper to check the wear pattern. To find out the truth.