2. best-of
  3. 127783-435

Audiophile fuses - Synergistic Black fuses vs the còmpetition

Between friends samples and onew I havd bought I find that these Synergistic fuses to be the best balanced. And without question inner detail .I originally had Hifi tunING supreme.which are good  but not in the SR class 
The Audio horizon I found more tipped up compared in certain areas furutech were no where's as detailed . The SR  Black fuses use the latest in Graphene  technology everyone from Nasa 
To the latest hi tech 3d printing and many 1,000s denser then Copper.Silver or Platinum.
All super computers are now using and soon home computers it is much faster and accurate.
But also smoother and more organic sounding parts connecxion if you purchase at least 3 or more 
May give you a respectable discount. Email Chris the owner at Tech go to the site . Lucky I only had 5 in my system. One thjng that was surprising is that I put one in my JL audio  Subwoofer  thd bass was noticeably more accurate and articulate.  2 thjngs to mention .these fuses take up to 200 hours to fully runin.but after 100 hrs 90% of the runin  is complete, also  Always go up to the next size ,for standard cheap steel fuses can vary up to 15%,where these fuses are typically within 
1%.  I found that no fuses popped .on a Modwright pre I popped 2 , then went from 2 to 2.5A
No problems and Make sure you get proper  slow-timed ,or Fast blow. A No Brainer like a very good cable upgrade and comes with a 30 day money back guarantee. 
128x128audioman58
dlcockrum's avatar
dlcockrum
2,190 posts
 
"Those were in self defense perhaps which is different."

mapman,

audioman probably felt the same way above following your post: "That might be fake news previously known as made up stuff."

If you are speaking only for your reactions in the other thread, then fair enough. In no way can this be attributed to the others. They inserted themselves into that thread with the sole intent of ridicule and mayhem.

If folks stop posting here about their positive experiences due to fear of personal attack, this forum will serve little purpose IMO.

Dave
mapman's avatar
mapman
22,334 posts
 
well in my defense I did not attack the poster rather challenged what was asserted which was not personal opinion all are entitled to but specific metrics cited. There is a lot of made up stuff presented as fact that goes around confusing people. Some seem to make a career of it with no remorse. Its important to challenge questionable assertions.  
mapman's avatar
mapman
22,334 posts
 
Also audio mans response was to call the critics ignorant rather than present info to defend his assertion about the fuse tolerance. Wrong! He should be taken to task accordingly as well for that. 
almarg's avatar
Ag insider logo xs@2x
almarg
9,670 posts
 
FWIW I have never seen a +/- tolerance specified by any manufacturer of any fuse for either current rating or melting point. What is generally specified by Littelfuse and Eaton/Cooper-Bussman for their fuses, in addition to the nominal current rating, nominal melting point, and various other specs, are the minimum and maximum opening times for various percent overloads relative to rated current. For example, the minimum and maximum possible opening times when the current being conducted is 200% or 400% or various other percentages of the current rating of the fuse. Those tolerances (the differences between min and max) are usually fairly wide. I have never seen that kind of specification for any audiophile-oriented fuses, however.

Regards,
-- Al

stevecham
3,340 posts
 
You know, I’m game for an experiment and I just moved and am setting up the new listening room, so, when the dust settles I think I will try a couple of these and report back. Look I do know cables make a difference and tubes do too so, what the heck, I’ll give it the old college try. There, is that fair? After all, it’s only wire.
More to discover