2. misc-audio
  3. 128637-2248

Owens Corning 703 vs. Roxul Safe 'n' Sound?

I'm going to make some sound absorbing panels to place on the wall behind my listening chair. Owens Corning 703 and Roxul Safe 'n' Sound rigid boards are two choices to make them with. Anyone have experience with both, or even one?
128x128bdp24
bdp24's avatar
bdp24 OP
9,788 posts
 

I didn't expect the extra space behind the panel to turn it into a bass trap! Just to lower its effective absorptive range a little. In the specs chart, it looks as if the Rockboard 60 may be a little better at higher frequencies than the 80, though the difference is marginal and perhaps insignificant. I don't want to over think this! But since the listening position has to be right up against a wall (to allow my dipole speakers to be positioned 5' from the wall behind them), and low-frequency eigenmodes run along room boundaries, absorption at as low a frequency as easily possible would be nice.

So I went to Home Depot last night, and though the HD website stated that the branch I went to had Safe 'n' Sound in stock (even the number of packages), I couldn't find any on the shelves. The HD "dude" couldn't even find it in the stores computer, telling me any acoustical product would have to be ordered. I went in to look at the stuff, to see if it is soft and loose like fiberglass insulation, or stiff like OC703. So Monday I'm going to Lowes, whose website indicates it has 2' x 4' Safe 'n' Sound in stock. We'll see!

sbank's avatar
sbank
3,378 posts
 
@bdp24 I feel your pain, with both HD & Lowes the inventory often doesn't match what online says is there. A frequent time waster. 

Your plan sound solid. If you do want more low freq absortion (i.e. bass traps for those front corners, rock wool was what was recommended to me by an acoustics specialist who consulted on my room and built my custom stuff. The 703 for wall and freestanding panels, but rock wool for the corner bass traps to maximize absorption relative to their volume. Cheers,
Spencer
bdp24's avatar
bdp24 OP
9,788 posts
 
Thanks Spencer. I had a session today, and the studio owner had real good acoustical treatment of his walls---a mixture of RPG diffusors and absorbers. I have a couple of spare 9" x 3' ASC tube traps---maybe I'll put them right behind the listening chair, with a couple of 2" x 2' x 4' panels stacked on top, for higher frequencies.
bdp24's avatar
bdp24 OP
9,788 posts
 
I was back near the same Home Depot today with a little time on my hands. I went in and looked for the Roxul Safe ’n’ Sound myself this time, and found it right on the shelf. S’n’S is 3" thick, and soft and loose, very limp, not at all like the OC703 semi-rigid panels, but more like cotton batting. Acoustimac offers empty 24" x 48" DIY panel frames in various depths, including 6". I’ve read that having a space behind the acoustical material will increase a panels ability to absorb low frequencies---a good thing for me due to the listening position being so close to the rear wall, but what if I was to stuff the frame with two layers of the 3" thick S’n’S? Possessing it’s 2.5lb. density, a 6" thickness of S’n’S won’t reflect back much of the mids and highs hitting it, but will that thickness absorb more, or less, lower frequencies than will a single 3" layer with a 3" space behind it? Acoustimac offers the frame both with and without a thin plywood rear back panel. Since my panels will be right against the wall, I surmise that back wouldn’t affect its performance.
auxinput
2,920 posts
 

I had to google around and think about this question. There really wasn’t a good answer, but...

Putting an air gap behind the panel is not going to absorb more mids/highs that are already being absorbed -- unless you pull the entire panel away from the wall. This allows mids/highs that are coming around the panel to reflect off the wall and into the back side of the panel.

I have read that an air gap behind the panel will enable the panel absorb bass that is an octave lower, but remember that any bass waves going through the panel are going to resonate the wall as well. If you look at the difference between Owens 703 2" and 4".  You’ll see that the 4" thickness is 5 times as affective at 125 Hz (0.17 vs 0.84). Based on this, I’d stack two layers of 3" to make a total of 6" if I wanted to absorb more bass. The "air gap" is really just a tweak to boost bass absorption on thinner panels.

More to discover