Computer PS Upgrade (Fuse/IEC/Teflon Cap)


Today I successfully installed a PCB fuse holder into my computer’s power supply. The stock fuse had leads soldered to the ends that were then soldered directly to the PCB. It took careful work with the Dremel to widen the PCB inlets to accept the fuse holder and now I can roll fuses with ease. I’ll soon order an SR Black fuse to replace the stock fuse rated at 6.3 amps/250V (5 x 20mm).

The power supply used only 1 film cap and it was rated at 1uf that was replaced with an unused Aura-T teflon cap that was sitting idle on a shelf. The power supply will help burn in the cap. Hopefully, the cap improves the sound of my generic computer which is my main source of music. There are too many teflon caps currently burning in since the acquisition of a Conrad Johnson 150SE; therefore, it will be difficult to distinguish what exactly is attributing improvements or detriments to my system but I cannot complaint at this point because my system sounds good. Today’s soundstage is more holographic than yesterday’s. Let’s see what tomorrow brings.

I noticed that the power supply’s IEC inlet is easily replaceable. It will be replaced by an Oyaide Inlet R that is currently in my modified Running Springs Audio Haley. I plan for the Haley to use the Furutech FI-06 NCF IEC or possibly purchase another Oyaide Inlet R for the computer.

Has anyone else tweaked computer electronics and what was your experience?
c_avila1
Post removed 
Before: 
http://i64.photobucket.com/albums/h162/triggr_357/Before%20IEC.jpg
http://i64.photobucket.com/albums/h162/triggr_357/Before.jpg
http://i64.photobucket.com/albums/h162/triggr_357/Before%20IEC%20Chasis%20View.jpg

After:
http://i64.photobucket.com/albums/h162/triggr_357/NFC%20IEC.jpg
http://i64.photobucket.com/albums/h162/triggr_357/Complete.jpg
http://i64.photobucket.com/albums/h162/triggr_357/NFC%20IEC%20Chasis%20View.jpg

The project has been completed with a few changes:
  • The Furutech FI-06 NCF inlet was installed into the computer's power supply instead of the Haley power conditioner. 
  • An Audio Horizons fuse was installed instead of the SR Black fuse.
  • IEC ground wire to pcb was upgraded to 16 awg, solid core, PVC insulated, copper wire. 
  • IEC neutral wire was upgraded to 20 awg, solid core, PVC insulated, silver wire.

Am I able to hear changes or improvements as a result of this project? There is absolutely no doubt about it! This what I hear:

  1. A much blacker background
  2. Sound stage focus
  3. Improved 3 dimensional imaging
  4. More detail
  5. Smooth, much less fatiguing sound
I expected to hate the sound of the rhodium IEC but I'm surprised that the tonality didn't change.

It's possible that this project provided only 1 improvement which is the black background. The sound stage focus, improved 3D imaging, more detail, and smoother sound are by-products of the black background. 
OP, have you tried any of the optimizing programs? I use Fidelizer and was impressed by the improvement in sound quality.
Also, did you record the changes with each upgrade? I'd like to know which ones affected sound quality.
B
Congratulations on your experiments and very positive results! There is a lot that can be done to improve the computer music system. The Synergistic Research Black Fuse will make a real difference and combining that with the Fidelizer software program (which optimizes Windows to play better  music) will give a real sonic change.
The computer is an incredibly electrically noisey device. Adding Synergistic Research Electronic Circuit Transducers (ECT's) to the computer will help diminish this noise.
Good luck on computer tweaking and please keep us posted on your results.

David Pritchard