2. speakers
  3. 134123-108573

Waiting on 802D3 to arrive -- Will I need a sub?

It's a rainy gray Sunday afternoon here in Atlanta today. I probably have better things to do but I've spent hours reading and researching trying to ascertain if I will need a subwoofer(s) once my B&W 802D3 arrive here in another week or so.

I can't decide and so I've decided to try posting here and crowdsource an answer, ha ha!

My goal is to create a system that will allow me to listen to 2-channel music for hours on end without fatigue.  The room is my living room and is a quasi open floorplan. It is around 24 feet long by 18 feet wide.  There are 10ft ceilings with an open stairwell back behind the seating position and an opening to my dining room that adds another 400 square feet or so of floor space.

Previously I've had B&W 804D2 towers with two B&W ASWCM10 powered subs.  I've sold the towers and the subs and am waiting on 802D3 to arrive as mentioned above.  The 804D2 absolutely had to have the subs.  The bass just wasn't there without them unless I really cranked the volume up.

So as I sit here I'm wondering if I made a mistake in selling my subs already.  With the 802's will I miss them or will those guys have me covered for 2 channel listening?

If it's likely that I will still need a sub (or 2) what do you guys think would be a good match to the 802D3?

Here is the rest of my equipment in case its helpful in offering an opinion:

Preamp:

·     PS Audio BHK Signature Preamplifier

Amplifiers:

·     Qty. 2: PassLabs XA60.8 Monoblocks

Inputs:

·     PS Audio DirectStream Junior (DAC)

·     VPI Traveler 2

·     Audio Technica AT33EV Phonograph Cartridge

·     Apple TV 4K 

Power:

·     Qty. 2: PS Audio P5 Power Plant

 Other:

·     Pro-Ject Tube Box S Phono PreAmplifier

 Speakers:

·     Bowers-Wilkins 802D3


Thanks!
Bryce
brycethomason
jgandy
28 posts
 
I also live in Atlanta.  Contact me if your would like a demo of what an added sub can do for a stereo setup.  I have JBL M2s supplemented with a JBL Sub18 which is driven by a bridged Crown ITech5000HD. (5000 watts into 4 ohms).  I have 4 B&W 801s in my multi-channel system for comparison.

jim.gandy14@gmail.com
georgehifi's avatar
georgehifi
10,312 posts
 
brycethomason
  Waiting on 802D3 to arrive -- Will I need a sub?
Not if you have an amp that can really push some high current into the bass, which has that demanding impedance/phase curve between 70hz to 1khz, especially at 70hz with 4ohm and 64 degrees of - phase angle which will seem like a 2ohm load to the amp.

https://www.stereophile.com/images/616BW802fig1.jpg
John Atkinson
" However, it is a relatively demanding load for an amplifier to drive. Fig.1 shows the B&W's electrical impedance (solid trace) and phase (dotted trace). The magnitude drops to 3 ohms between 100 and 130Hz, and again between 670 and 770Hz; and while the electrical phase angle is low in the lower region, it becomes increasingly inductive above 600Hz, reaching +46° at 1kHz, where the magnitude is 4 ohms. There is also a combination of 4 ohms and –64° at 69Hz, implying that this speaker does require an amplifier that is not upset by a low effective impedance.
Read more at https://www.stereophile.com/content/bowers-wilkins-802-d3-diamond-loudspeaker-measurements#p1WfY2vha...

Cheers George

brycethomason OP
18 posts
 
I want to just thank everyone for all the input and advice.  I've thoroughly enjoyed hearing folks from both camps. You all are certainly experts with well thought out opinions.  The one thing that is truly clear is that at the end of the days it will be left in the 'ears' of the beholder.  The 802d3s arrive on Tuesday of next week, so I'll know what suits my ears soon enough. 

The deal to sell my two B&W ASWCM10 (not the cm2 mind you) subs fell through, so I actually still have them.  I'll just hold on to them so I can do some a/b testing with them.  I don't know if they will do justice to the towers the way a b&W flagship sub like a DB-1D would but at least I'll have them to make that call here shortly for myself.

Again, I've enjoyed the hell out of this conversation and send a heartfelt thanks out for some seriously great engagement on the topic from this community.  Thanks for the help!
dualmarantz
18 posts
 
bdp24: "The bottom octave is a bitch to reproduce, and very, VERY few speakers are up to the task."

I would amend that sentence: "The bottom octave is a bitch to reproduce, and very, very few ROOMS are up to the task."

bdp24's avatar
bdp24
9,816 posts
 
There is that too, dualmarantz! To find the locations of the resonant modes in your room (via the calculators on the net; modes are generally along all the wall/floor/ceiling intersections, and at the 1/2, 1/3, 1/4 divisions of the length, width, and height of the room), and avoid those locations for your equipment rack, speakers, subs, and listening chair, is a good start. If you can afford them, install "true" bass traps (not those flat pieces of Owens Corning 703 wrapped in cloth that some companies market as bass traps) in those mode locations, to soak up the standing waves. OB subs are a way to excite fewer of those modes to begin with, but most people don’t want to go there.
More to discover