Romex and breaker switches


I did a search and have read previous posts, but I still have some questions. I had an electrician install dedicated lines in my listening room when we built our house 20 years ago. I bought simple hospital grade outlets from a big box store and did not specify the gauge of the romex or anything else. I need to clear out my dedicated listening room soon for new hardwood to be installed and figured now would be a good time to revisit and improve my dedicated lines. I have already bought a pair of Oyaide R1 duplexes and intend to have them installed side by side behind my equipment rack. My question is-is there a particular variation of 10 gauge romex that would be best? I have looked and there are quite a few variations including 10-2 and 10-3 and I have no idea what to buy or for that matter, if some other wire that would do the job and not be prohibitively expensive presents a better option. I will need a 20 foot run for each duplex. Also, can someone help me as to whether the breaker switch on my panel matters much and whether I should opt for 20A, 30A, or other? I now know that all runs from my duplexes to the panel should be to the same leg. I will make sure that happens. Any other recommendations or advice about romex/wire to use and breaker switches given my decision to go with Oyaide R1's would be most appreciated. 
128x128fsonicsmith
I'm with Jeff. Run two 20 amp 12-2 lines directly from the breaker panel. Use whatever breakers your box takes Murray for Murray, etc.
Dedicate one circuit to the power amp. 

No pig tailing bigger wire to smaller. No using a 30 amp breaker - you want it to trip if there's a problem!

I heard BX painted metal flake electric blue sounds best. As long as the flakes in the paint are aligned by an electrostatic cyrocoating process.
Contact Chris at VH Audio.  He will be able to steer you in the right direction and he has all you need at his facility.
audioslain02
"There can be advantages to using 10 gauge wire on a 20A circuit, including reducing voltage drop. It is difficult to work with, and using a pigtail into the outlet does make it easier to terminate."

Not only is this a Code Violation, this is a MAJOR fire hazard.
Tha ampacity of the wire cannot exceed the ampacity of the
breaker.
You misread what I wrote. It is certainly within code to use 10 ga. wire on a 20A circuit, which requires by definition a 20A breaker. There are large potential advantages to doing just that, and it has worked very well in my system. It is actually a fairly common practice and exceeds the NEC, which only sets minimum standards.


For your short runs I'd recommend 12-2 wire on 20 amp dedicated breakers, as others said it will be easier to attach to your outlets, and should you ever decide to switch out your outlets in the future it will be easier and lessen the possibility of damaging your AC outlet when you have to push the outlet back into the outlet box (I've been there and actually broke some high-end outlets).
In my main system, I have six dedicated outlets that are between 50 to 60-foot runs. I experimented with 12 and 10 gauge wire including cryogenically treated wire. I honestly could not detect a difference in sound or performance, however, I realize for peace of mind many will suggest 10 gauge wire and/or specially wire.
I do hear a difference with cryoed vs non-cryoed AC outlets.
@fsonicsmith - have the electrician install two seperate runs of 12-2 or 10-2 - one for each outlet.

Also if the runs have to go through studs, have the electrician drill seperate holes for each cable.

Have them position the cables at least 1.5 inches apart

The electrician will maintain it makes no sense and you should go with a single 12-3 or 10-3, but be adamant about this. 

I have tried both and two totally seperate runs of 12-2 on the same leg  as detailed above provided better sound quality than a single run 12-3 on the same leg.

I believe the improvement was due to Proximity Effect. (google it)

There are differing opinions on whether the effects of this phemonima is a real concern - some go into long winded mathamatical proofs prooving it to be of no consequence, but in my book - actual observation trumps anything else.

FYI - I used Pass and Seymour MRI plugs (no ferous materials used) - they clamp like a vice and are reasonably priced
https://www.takefiveaudio.com/categories/214-pass-seymour-cryo-treated-15a20a-wall-outlets

Regards - Steve