Cartridge Loading- Low output M/C


I have a Plinius Koru- Here are ADJUSTABLE LOADS-
47k ohms, 22k ohms, 1k ohms, 470 ohms, 220 ohms, 100 ohms, 47 ohms, 22 ohms

I'm about to buy an Ortofon Cadenza Bronze that recommends loading at 50-200 ohms

Will 47 ohms work? Or should I start out at 100 ohms?

I'm obviously not well versed in this...and would love all the help I can get.

Also is there any advantage to buying a phono cartridge that loads exactly where the manufacturer recommends?

Any and all help would be greatly appreciated.

Thanks in advance.
krelldog
Will 47 ohms work? Or should I start out at 100 ohms?


You have to try it. There is no Standard (unfortunately). The result will be different from Manufacturer to Manufacturer. Phonstage A with 100ohm will not sound identical to Phonostage B with 100ohm...Depends on Design.
Dear @almarg : I understand all what you posted and that's theory behind.

When I said if you have first hand experiences/attest for that what I'm trying to say is that with a normal phono stage design that normally comes with fixed capacitance value for LOMC cartridges and options for the loading impedance . This is what I'm refereing to.

As Syntax pointed out each phono stage comes with way different kind of designs. So what's your advice to audiophiles about? that because they can't change the capacitance value or don't have money to change too the phono cable then what?

Makes no sense advices as the atmasphere about because there are several many other cartridge set up parameters way more important. All of us must work with what we have using it in the best way we can. The capacitance issue has other implications with LOMC but this not the issue but what exist in the market about.

You are happy with the Herron, good for you but are many way better phono stages with different design to Herron. Try to say or imply that a single characteristic makes the " differences " like the capacitance in LOMC cartridges has no sense. The theory has sense but this is not the issue.

I think that analog is full of severe problems fopr we can enjoy it to now start to worry about capacitance. Go figure ! !

As I said, there are other issues extremely more important where we audiophiles have control with out spend money.

Makes sense to you that now all audiophiles must do something on capacitance? because the common sense of J.Carr says something different in his Lyra site.

Again, I'm not against  that theory but about ist real advantage  especially when before the capacitance issue many of us are trying to know how can we  achieve an accurate tonearm/cartridge/TT alignment that even reviewers today some of them just don't understand the theory behind that kind of critical alignment issue.

@krelldog , don't distress. Makes no changes just make the cartridge tests with what you have and follows what syntax posted. You have to try it, makes tests with what you have before any other thing. Forgeret about theory in that specific regards. Some people try to terrorize to all of us simple audiophiles. No J.Carr never did or does.

R.
Hi Raul,

With regard to the OP's situation, all I was basically saying is that he is likely to obtain better results using the 100 pf setting of his phono stage rather than the 570 pf setting, assuming that he optimizes the resistive loading that is used with the 100 pf setting by listening.

Regards,
-- Al 
There is a massive misunderstanding that seems implicit with Raul's post, which is not surprising since Raul  prefers digital audio... no idea why he posts here.

This is not about money, its the physics of why its worth it do to it right, which does not cost any more. If your phono section is requiring that you use loading resistances, follow my suggestions here and above.

Input capacitance is a thing with all phono sections. It can be considered to be in parallel with the cartridge inductance, and so reduces the resonant frequency that is always present, which should be kept as high as possible. If ever there was an argument for a vacuum tube input, this might well be it, since tubes have far less input capacitance.
Alternatively, if one were to use a stepup transformer, the transformer blocks the RFI resonance due to bandwidth limitations and may well be why some people prefer using an SUT with their phono sections. SUTs are their own bag of tricks- to get them to work right, they have to be loaded at their output to prevent the transformer from ringing (distorting). This value is different for every cartridge as each cartridge has a different impedance and transformers transform impedance. Usually the transformer manufacturer will have an idea of what the correct loading will be (a good example in this regard is Jensen, who also makes some of the best SUTs made).

At any rate, keeping the cable capacitance low is important for proper phono reproduction! @krelldog , there are no specs (just 'features') on the page you linked.

If no SUT is used, one should always start with 47K since that is the industry standard and has been for decades. This value is used because its less susceptible to noise that a higher input impedance might be, while easily driven by moving magnet cartridges which are very susceptible to loading at audio frequencies, unlike moving coil cartridges (unless the latter is high output, since its the inductance that causes the susceptibility). From there reducing the loading resistance can be explored if needed.

**The highest value you can use is recommended for best results.**

That can be considered a general rule of thumb.

Again, if the phono section is unstable or has poor overload margins the result will be more ticks and pops. People often ask me how I get such low noise reproduction without ticks and pops and that is the secret. Many people grew up with unstable phono sections (most Japanese phono equalizers made during the 60s, 70s and 80s were unstable) and so just assume that ticks and pops are part of the LP experience, but it does not have to be that way.
Dear @almarg : " basically saying ", now I understand you and now your advise is useful when the post of the atmasphere it's not for the OP.

But he always post with a hidden agenda that sooner or latter comes out like in this regards:

for a few time ago he was posting here and elsewhere the same about that capacitance LOMC issue and he just posted here:

"  People often ask me how I get such low noise reproduction without ticks and pops and that is the secret. "

why he posted that? no one is asking for but he did it because he is a seller a very agressive seller that always post with a hidden agenda. Now, the ones that read here know that his electronics are just " perfect ".

I'm not against any manufacturer as him what is not valid is to post trying not really to help ( as you ) but to sell " something ". It's the same with TP tonearms and everything where he has or look for a bu$ine$$.

"""  Raul prefers digital audio... no idea why he posts here  ""

well I don't know why this forum permits to a seller to promotes in an audiophile threads because he never gives an advice as an audiophiile but as a seller. He is not like J.Carr that posted and post in Agon and other forums and you will never read JC promoting anything he doings only gives honest advices as an audiophile. 

Time to report it.

R.