Ohm Walsh Micro Talls: who's actually heard 'em?

FWIW, I have read reviews from MWT owners that indicate bass levels is not a problem even in larger rooms. Certain recordings that plumb the lowest octaves and do it well benefit most from adding a sub. A good pipe organ recording is a typical case.

For a lot of popular and mainstream rock recordings, a sub may not do much in terms of delivering more bass that is also "clean". Its contribution will certainly be less in most cases.

I use an old M&K sub with my OHM 100S3s in my large family room/kitchen area. The 100s are somewhere between 1000s and 2000s in size as I recall. All are larger than MWTs. The sub is set at a very low level and crossed over as low as possible with that sub, at around 40-50hz or so. The level setting is quite minimal, around 1 or 2 out of ten. I could probably live without it 98% of the time.

One other thing worth noting with all OHM Walshes and bass is that they are all bottom ported and can interact with the common wood particle board floors used in many modern homes including mine in ways that strongly affect the bass.

In my case with the 100s, that sit on the 4 factory installed wooden feet, I find the bass a tad "boomy" when sitting directly on the thin carpet 2nd level particle board floor. There is some resonance that occurs. This could vary home by home, room by room, but having owned OHM Walshes in one form or another since 1981 I would say it is typical. I solve the problem in my case by placing each ohm on a 12'X 12" ceramic tile from home depot. This provide just the right amount of additional dampening in my case.

My much larger OHM 5s are on the factory provided castors (great for tweaking location easily) and on the first level and sit direct on the house's thinly carpeted concrete foundation. Floor interactions from the bottom ports there are a non issue and the bass there is reference standard quality in my assessment.

The damping factor of the amplifier used is another thing that can strongly affect how the bass sounds. I like the highest damping factor possible with mine. My Bel Canto ref1000m amps have 1000 damping factor and the bass is deep, full and articulate, just right! My TAB 125 Hibachi's have somewhat lower damping. WIth that, the bass is just a tad not as "tight". SOme bass fans may like that and some may not. It's a judgement call for the most part I would say.

I find damping factor still matters with my smaller 100S3s, but less so. The TADs sound just right with those.

In general, I would estimate any good SS amp, 80 watts/ch or higher with damping of 50 or higher should be a good candidate to drive MWTs. More power up to 250 w/ch or so might benefit bass as well, in particular at higher listening volumes.

Finsup:

Speakers:
Left/Center/Right: 3xOhm Walsh 100-S3
Left/Right Surrounds: 2x 100-S3 in Ohm Walsh 2 cabinet
Left/Right Rears: 2x100-S3 half-sized and in omni config.

Subwoofers:
4xEpik Empire-2 up front and 2 to side of listening position

Electronics:
Oppo BDP-83 blu-ray player
Yamaha RX-V765
Emotiva XPA-5 Amplifier (for LCR and surrounds)
Outlaw 7125 Amplifier (for rears)
SVS AS-EQ1 subwoofer equalizer

Display:
Panasonic AE-4000U front projector
100 inch acoustically transparent screen

Cabeling:
Monoprice

Room:
12.5x17x8
listening position about 9 feet from screen
Some acoustic treatments and dark curtains/rugs

I got the surrounds, Empires, Yamaha, XPA-5, 7125, AS-EQ1, Panasonic, and screen at steep discounts (on sale/used/rebates).

I would love to hear that OHM Walsh based surround sound system!

I am not a surround sound fan in general and do not do that currently, but I suspect I could live with that one!