Nuprime cdt 8 transport.
Home Theater Receiver recommendations for B&W 803S?
Hi! I'm on the hunt for a new receiver, since I recently upgraded my main speakers, and I'd like to have one that also passes 4K signal.
My current setup:
Denon AVR-4308CI
Left & Right: B&W 803S
Center: B&W HTM2
Surrounds B&W 301
Sub: Energy 8"
I recently upgraded to the 803S's on the left/right; replacing my original Nautilus 805's. Now I need to upgrade the rest of the system!
I think the first step is the receiver, especially since I'd like to be able to pass 4K to my projector. Then will likely upgrade the sub (Am considering the Monoprice Monolith, 10" or 12"...). And I'm also on the hunt for a HTM3S, to better match the 803S's.
I'd love to know what Receiver recommendations folks have that will pair nicely with these speakers. Ideally under ~$2K - and I really don't care much about other bells & whistles (multi zone, bluetooth, wifi, whatever). I'd rather the money go into the best possible D/A, amplifiers, etc... and leave other tech gadgetry to other boxes.
Appreciate any/all input! Thanks! :)
My current setup:
Denon AVR-4308CI
Left & Right: B&W 803S
Center: B&W HTM2
Surrounds B&W 301
Sub: Energy 8"
I recently upgraded to the 803S's on the left/right; replacing my original Nautilus 805's. Now I need to upgrade the rest of the system!
I think the first step is the receiver, especially since I'd like to be able to pass 4K to my projector. Then will likely upgrade the sub (Am considering the Monoprice Monolith, 10" or 12"...). And I'm also on the hunt for a HTM3S, to better match the 803S's.
I'd love to know what Receiver recommendations folks have that will pair nicely with these speakers. Ideally under ~$2K - and I really don't care much about other bells & whistles (multi zone, bluetooth, wifi, whatever). I'd rather the money go into the best possible D/A, amplifiers, etc... and leave other tech gadgetry to other boxes.
Appreciate any/all input! Thanks! :)
- ...
- 95 posts total
Couple of things I’m going to re-iterate. That digital COAX cable is good for everything except a few scenarios: - Bluray with Dolby TrueHD - Bluray with DTS-MA HD - Some streaming that uses Dolby Digital Plus. I have seen sometimes if you try using digital COAX for Dolby Digital Plus where the sound may have "skipping" problems every few seconds when the processor tries to synch or it may only give you the 2-channel left/right channels. In this case, you must use Dolby Digital Plus over HDMI. ---- Feel free to upgrade your bluray player if you want. It might improve the sound a little, but I don’t think it will give you that visceral and spatial imaging you are craving. And the digital COAX will, ultimately, only improve the sound on 2-channel PCM audio and old DVD movies. ---- " lack of clear imaging " - heh, I keep recommending this fuse upgrade because it is such a cheap investment, it’s almost a no-brainer. While the Marantz is very excellent at giving a full and true sounding waveform, it is rolling off the upper mids and highs. The fuse would put the audio back into focus and would really improve clarity and spatial imaging. A power cord upgrade can also help here, but it becomes hugely more expensive and it can be difficult to match the proper power cord. Making the highs more clean/clear could help reduce that "fatiguingly bright" effect because a warm sound will actually smear the highs and make them more harsh. Or, it could be that you are just now hearing the problems with those aluminum tweeters on a full range system. Or it could be you are hearing problems with harshness caused by the low cost interconnects, or even low cost stranded speaker wire. lol. Stock power cords can also create a bright/harsh fatiguing sound on a very high resolution system. Welcome to the wonderful world of tweaking audiophile systems. ----- For acoustics, if you definitely have a bass resonation in that corner behind the speaker, then putting a GIK Acoustics "Soffit" or "Tri-trap" in that corner will help. You can even stack two to make an 8 foot high bass trap. --- For that particular speaker, I would also put a normal acoustic panel right on the wall just in front of the speaker. This would be a normal 2-3" panel, like the GIK Spot Panel. Since the speaker is only a few inches away from the wall, it actually uses the wall to act like a "horn" that boosts certain frequencies with that first reflection point. Not a good thing, lol. Or I can advise you on how to make your own panel (it’s just some Owens 703 fiberglass that is covered with fabric such as Guilford of Main or something). |
Ok, you've successfully twisted my arm about the fuse upgrade! I just opened up the Marantz and pulled the fuse, so I could figure out which to buy. Looks like it's the 5x20 size. The circuit board and the etching on the fuse are T2AL/250V... From a bit of Googling, it looks like this means: T = slow blow 2A = 2 amps L = glass 250v = rated voltage My best guess is that I should get this one: https://www.partsconnexion.com/FUSE-80979.html Though that one appears to be an extra slow blow. Will that matter? I also just read a few reviews and commentary on fuses, and of course started going down the rabbit hole of various other options (and reading lots of arguments about whether fuses are "snake oil" or not...). Anyway, if i'm going to swap out the fuse, I'm willing to spend a few more bucks if it'll be an even more notable improvement. The fuse isn't particularly easy to get to in the Marantz...have to pull off two covers, and then remove another circuit board. Doable, but it's not something I want to be doing often. So if I can get a better fuse now for a few bucks more... I saw the Supreme 3 available around some shops for $60 to $75... and then there's the Synergistic Blue for $150... will spending more on those likely yield any better results? |
Just came across this power cord on Parts Connexion... wondering if it might be a good choice for either the Rotel or the Marantz, especially since it's 10awg. Tried to find info on "Connex" cables but didn't turn up much. https://www.partsconnexion.com/CONNEX-76701.html |
- 95 posts total