2. tech-talk
  3. 148385-42281

Ground Loop(?) leads to blow speaker

Aloha 'goners!
          I'm going to do my best to get the details down here as I am a bit stumped on this one.

I have a Wadia 121 DAC that was recently repaired.  The issue was the RCA/XLR outputs produced mostly noise and little music.  The headphone side was fine.

As the unit wasn't functioning properly I hadn't had the chance to hook it up and use it.  When I got it back and hooked it up there was a nasty ground loop(?) that led to a blown speaker (Thiel 1.6).  The buzz produced was the angry bee buzz followed by a loud electrical sounding crack and the woofer was gone.  The amp (Creek Classic A53) went into protect mode and I shut it off.  I then disconnected the Wadia and hooked up a Mytek Brooklyn+ and there was no buzz.  Same cables same outlets same everything except the DAC.  I tested the amp and it seems to be ok through another pair of speakers.

At this point I wasn't sure what was going on.  I tested 3 different amps with the Wadia and 2 of the 3 buzzed.  With the Mytek none of them buzzed.  Of the 2 amps that buzzed one of them had a 2 pin connection and the other a 3 pin.  The only amp that didn't buzz was a 2 pin Adcom 535 MkII.  The other amps were a 3 pin Creek and a 2 pin Carver.

Here is the full chain:

Primare CD31 --> Madrigal AES Cable --> Wadia/Mytek DAC/preamp --> Chord Cobra Vee RCA --> Creek/Adcom/Carver amps --> Tara Labs spkr cable --> Thiel 1.6/B&W CDM1SE speakers

I used the same wall outlets for the DACs and amps.  The same interconnects were used between components as well as from the amps to speakers.

I tested the wall outlets with a cabling tester and it said they were wired correctly.

Could there be something else that I'm missing that would be causing this?  The only amp I am comfortable with using to test is the Carver as it has a variable level on the front panel.

Any help or thoughts on this would be greatly appreciated.

solobone22
almarg's avatar
Ag insider logo xs@2x
almarg
9,670 posts
 
P.S: Now that I think of it I presume that "2-pin" and "3-pin" were references to the number of prongs on the power plugs of the amps. And since the problem appeared when you used the Carver which has a two-prong plug that would seem to further confirm that the problem was unrelated to a ground loop.

Regards,

-- Al
gs5556
1,239 posts
 
The Adcom 535 Mk II is capacitor coupled at the input and the Creek and Carver are not. What you have is DC at the output which the Creek passed through to the speaker before going into protection mode. The Adcom's input cap blocked the DC and didn't pass the buzz-causing DC to the speaker. DC is enough to blow out a woofer.

The problem in the DAC can be anywhere in the active circuit. I would present a repair bill for the Thiel to whoever worked on the Wadia.
gregdude
222 posts
 
+1 to everything gs5556 said. A ground loop would be characterized as a hum. What you say you heard was a buzz, that blew out a woofer, almost definitely DC 
solobone22 OP
88 posts
 
Thanks Folks!

With regards to the 2 pin 3 pin I should have posted that I was referring to the power cable.

Working on measuring the output on the unit now. The place that did the repair wants the unit back however I’d like to measure it in its current state and then again after they send it back.
solobone22 OP
88 posts
 
I have a Klein Tools MM300.  I set the meter to 200m and tested the RCA output touching the positive line inside the connector and the negative line to the outer barrel.

The left channel read 1.0.
The right channel read -0.1.

This looks to be the culprit.
More to discover