Amp level versus line level inputs for subwoofers


I'm trying to learn something about subwoofers and have noticed that some subwoofers have a choice of input type. Could someone please explain the difference between these two types of inputs and the relative advantages and disadvantages of each?

Basically, I think a sub with both types of inputs can receive its signal from either the system's preamp or its amp. I assume that if the signal comes from one amp or mono amps, the sub would then retain more of the sonic characteristic of the main amplifier and less from its own internal amplifier.
peterayer
"I assume that if the signal comes from one amp or mono amps, the sub would then retain more of the sonic characteristic of the main amplifier and less from its own internal amplifier"

Thats what they say, but I don't buy it. The sub is playing different freq's than the speakers, so how could you detect this "sonic characteristic" flow through?

The speaker level connection is there for people that don't have preamp outputs.

Of course this is just my opinion, and you can try them both? Who knows?.......you may like one better than the other.

Dave
REL and a number of other sub manufacturers (and manufacturers of speakers with powered woofers) swear that best sound is achieved when sourced from the speaker outputs of the main amp - they claim that the sound is more coherent, as the sub picks up the "flavor" of the main amp. On the other hand, many hi-end manufacturers believe the amp input is a dirty source that is inferior in every way to a line-level input.

The answer will be system-dependent, i.e., best sound quality would be ensured by providing both line-level and amp inputs (presumably, this is not always done due to cost).
I use the speaker level inputs on a stereo pair of subs with great results both with music and movies. My subs have RCA, XLR and speaker level inputs.

I assume that if the signal comes from one amp or mono amps, the sub would then retain more of the sonic characteristic of the main amplifier and less from its own internal amplifier

I agree absolutely. Mine are not connected to the amp, but to the speaker binding post via bananas.
Line level comes from the amp output (or from the speaker) but is a very high impedance (on the sub) which means it is sensing the voltage and not using any real current to drive it. The best scenario (in my opinion) would be a sub out from the pre with a built in (or external that would go between the pre and the amp if not built in) crossover. That way there would be more available current for the speakers since that power won't be wasted on something the speaker can't reproduce audibly. Without a built in or external crossover that current is still going to the speakers. So if a crossover is not possible I would prefer line level.

Hope that helps
The interface between amp and main speaker is highly complex, and the signal that is present at that point reflects not only the sonic character of the amp itself (and what precedes it), but effects that depend on the speaker as well.

Those effects include phase differences between voltage and current, which depend on the degree to which the speaker's impedance is capacitive or inductive (as opposed to purely resistive), and also back-emf (voltage produced by a driver within the speaker due to its motion continuing after the signal has stopped or changed). All of those effects are highly dependent on frequency.

Since as Xti16 indicated the sub's amplifier only senses voltage and not current, its response to those effects will be partial, and will be essentially unpredictable. Whether the sonic result of that response will be for the better or for the worse therefore figures to be system-dependent, as Raquel stated.
I assume that if the signal comes from one amp or mono amps, the sub would then retain more of the sonic characteristic of the main amplifier and less from its own internal amplifier.
More of the sonic character of the main amp -- yes.
Less of the sonic character of its own internal amp -- no. I would expect the sub's internal amp to be just about entirely in the signal path to the sub's driver whether the input is taken at line-level or speaker-level. If it is taken at speaker-level, I would expect that the incoming voltage would either have a lower gain applied to it at the front end of that signal path, or else that it would simply be divided down to a line-level amplitude and then processed identically to a line-level input.

Regards,
-- Al