Trying to find someone with a cable cooker in Metro NY


Hello to all...

Have recently been 'exposed' to the concept of cable cooking to improve performance, but would like to pay someone who has one, to do it to my interconnects and speaker cables, each for a 3 day (72 hr) treatment... Would be nice if you are in the Metro NY area, but would be willing to ship to you if out of area.

Would also like to hear from someone with comparative experience (geoffkait?) in using this and/or cryogenic treatment: if results are different, one more effective than the other,  one more lasting than the other, must treatment be redone periodically?

Please relate real-life info ( don't be a second level whistleblower, passing relayed to you experiences...).

Best Wishes to all.
insearchofprat
Whether or not cable cookers and burning in cables actually do anything is irrelevant.  What it does do is remove any doubt you have about your system and make it so you are confident you are doing anything you can to have the best sound.  

For the record......Scientifically (and I am a scientist) I don't believe you need to burn in a piece of wire.    But I still made a DIY interconnect cooker just to stop that little voice in the back of my mind saying it will improve things and sound better without having to wait 200-500 hours.  For me it was worth the 1/2 hour to solder a few parts together from my junk bin. 


If someone needs to spend $1000 to make the voice go away I might shake my head a little but I understand.
delkal
For the record......Scientifically (and I am a scientist) I don’t believe you need to burn in a piece of wire. But I still made a DIY interconnect cooker just to stop that little voice in the back of my mind saying it will improve things and sound better without having to wait 200-500 hours. For me it was worth the 1/2 hour to solder a few parts together from my junk bin.


>>>>That’s a good point, but only in the sense that cable burn-in is fairly well agreed, you know, scientifically, that’s it’s actually the dielectric that’s changed by burn-in, not the wire. For fuses, who knows what burn in accomplishes? The solder joints? The air? 🤡
... One more day in the frig as the dwell down continues... Tomorrow afternoon the wires (and short jumper lengths I made) will come out and lie around in the stereo room, resting (like the recommendation for oven roasted meat) for a couple of days before they go back into the system.

geoffkait: will the treated wires need a break-in period again? if so, how long do you recommend? I am presently running another identical set - so should I Immediately hear a difference once I swap them in?
" One more day in the frig as the dwell down continues... Tomorrow afternoon the wires (and short jumper lengths I made) will come out and lie around in the stereo room, resting (like the recommendation for oven roasted meat) for a couple of days before they go back into the system.

geoffkait: will the treated wires need a break-in period again? if so, how long do you recommend? I am presently running another identical set - so should I Immediately hear a difference once I swap them in? "
  Love your sense of humor! Frig is priceless.
geoffkait....... " That’s a good point, but only in the sense that cable burn-in is fairly well agreed, you know, scientifically, that’s it’s actually the dielectric that’s changed by burn-in, not the wire. For fuses, who knows what burn in accomplishes? The solder joints? The air?"

Capacitors (and to a lesser extent tubes) are scientifically shown to need a burn in. You can hook them up to a tester and the differences after use are obvious. The cap manufacturers even state this and you can find it on their spec sheet. So I agree some components need burn in. 100%.
But scientifically I don’t buy the dielectric needs to burn in for a cable (a wire with insulation) and AFAIK no tester has ever shown a difference. Whether a person can hear something no machine made by man can detect is the debatable part. The dielectric in a cable is an insulator that can usually hold thousands of volts and I don’t see how a small voltage is going to change anything. But that is just me and I still had enough doubt to make a cooker and try it out (for free its worth it, I’m not paying $1000).

I made a burner for interconnects even though they carry an extremely low voltage/ current. I hooked up my speakers directly to the RCA output of a tuner and I had to put my ear to the speaker to hear anything. Even with line level CD output you had to be a foot or two away to hear anything. This got me wondering how this small amount of a current would ever effect a dielectric capable of taking 1000+ volts. But YMMV. Lets just leave it as there is no way I believe a phono cable needs burn in. They don’t carry enough power to even be audible directly connected to a speaker. How will that current ever change anything?

To further complicate things I also made my interconnects. I used small gauge wires (solid or stranded, pure copper or pure silver) and put them into an oversized Teflon tube. The wire is just randomly hitting parts of the Teflon and the the rest is just air. Like you mentioned how do you condition air? I am not sure this design even needs a burn in. But I did it anyway. If you believe the cable cooker spin I put at least 10,000x more voltage / current as you would get from line level in a couple of days listening to music (OK, I started drinking Scotch and the music got much louder than recommended at times). But now I know they are burnt in, no voices in my head giving me doubt and I can relax and compare my designs.