REL subs with Rowland Amplifiers

Richard, were you or were you not connecting your RCA ic to your preamp from your REL at the low level connection (LFE connection)? Because if you were, you are now activating your low level connect ( pushing signal as well as establishing a ground), I do NOT believe you can have both a high level and a low level at the same time...as I was told that if you do this, the low level takes precedence.

daveyf,

You do realize that the .1/LFE and low-level inputs are different? Although I didn't use .1/LFE I thought it was understood I wasn't referring to the low-level input. Since you won't listen to me, I have attached emails that I received directly from REL.

DIRECTLY FROM REL:

Richard,

You had been running the RELs low level. Instead of finding a place to connect the BLACK wire to the chassis, you can use RCA cables to make the signal ground connection.
I would connect between the pre-amp and the LFE RCA input of the RELs. The collar of the RCAs will provide the same connection that the BLACK wire if the high level cable would make.
Simply leave the .1/LFE Level control at minimum.

When you have a component system like this, all the components need to share the same ground reference. This is typically the signal ground of the system and is shared by both the pre-amp and the amplifier.
What I am instructing you to do is access the signal ground by connecting the PRE-AMP to the REL.

Yes, you can use make the RCA to RCA connection while still using the high level connection.

There are two input channels to the RELs.
1) the high level/ low level channel and
2) the LFE channel.

Each has it’s own level control.
The ground connections for both the these channels are connected internally to the REL. So connecting the RCA collar is like connecting the BLACK wire of the high level cable to the signal ground at the pre-amp.

Interesting Richard. I got the exact same advice from REL and then on a subsequent call was told that the LFE.1 channel takes precedence ( same as the low level connection). If it is connected via an RCA cable. The second adviser told me that i should just run a wire from the preamp to the REL chassis to establish just a ground and not an RCA cable...i did neither. No question that attaching the RCA CABLE TO THE PREAMP AND TO THE REL CREATES A GROUND.

I've already sent Rowland an email requesting the cost of adding an external ground screw. Hopefully they will respond tomorrow and I will ship my amplifier to them before the end of the week.

Al do you have any idea as to why my balanced JR model 8T has no issues when connected in the manner that i suggested? ( which also was the way that REL had suggested to me to do the hook up when I first acquired my sub).

First, it's noteworthy that while in the case of stereo amps having outputs that are not differential (i.e., that are not balanced or bridged) the many REL manuals I've had occasion to look at over the years recommend connections exactly as you have described (red to right positive, yellow to left positive, and the black to either negative connector), but not a single one of those manuals makes that recommendation in the case of amps having differential (balanced or bridged) outputs.

Second, while as I had mentioned that approach **might** work with amps having balanced or bridged outputs, depending on the internal grounding configurations of the sub and the amp, and in fact over the years I've seen a number of members here report doing exactly that with no apparent issues, at best connecting a full-amplitude amplifier output to the circuit ground of a sub is poor practice from a design standpoint, and at worst it could have the various adverse effects I described earlier. 

Just to cite one potential example:  I know that many Audio Research balanced amps connect circuit ground to chassis ground/AC safety ground with a 10 ohm resistor.  **If** the sub does likewise it would mean that a full amplitude output of the amp would be applied across a total of 20 ohms.  And if the two 10 ohm resistors have not been chosen to have particularly high power handling capability one or both of them could burn out, eventually if not sooner.  Resulting in hum and/or degraded sonics.

Is there a logical reason why when both subs are connected through the high-level input with the REL supplied speakon cable no hum is audible, but when I use the Signal speakon cables the hum is clearly audible? This is with no RCA cable connected to the RELs LFE inputs and into my preamps outputs.

I don't know.  But if you have a multimeter it might be worthwhile to verify that both cables are wired identically, and that no shorts exist between the yellow, red, and black wires of the Signal Cables.  Also, I see that the Signal Cable is described as being unshielded.  I don't know if the stock REL cables are shielded or not, but if they are perhaps the Signal Cable is picking up EMI from something nearby while the REL cable is not.  

Best regards,
-- Al