At the risk of being "neurotic and gullible" ;-), the gear you mentioned would certainly benefit with upgraded power cords. I do, however suggest that you get everything setup, working and some time listening to the system before you change anything. Get a feel for the system sound, then if you want, experiment with power cords, interconnects and speaker cable. Actually, I have found that power cords make very good changes to the sound of the overall system. IMO, Pangea and Signal cables are not good choices as they have produced a dull or muffled effect on the gear I have tried them with. There are many choices out there and one does not have to spend a fortune to get good results. Kimber, Zu and VH Audio have good value/performance offerings.
Advice/Warnings for a newbie
Hi
I've had way too much free time and gone down a few rabbit holes purchasing some older gear, some of which I've got a little experience with and some none... but was curious, because I am not the best technically, if any of the more seasoned audiophiles might have any advice regarding my chain. I'm replacing my 30w Pioneer receiver with separates (put all my specs in the below list) – I got the preamp as a family hand-me-down and I've just bought the monoblocks (having service done now) so I've not heard it all together yet. The player and speakers I've been using forever. But will I OK in terms of matching impedances, gain, etc? Oh, and I'm installing a dedicated line for the monoblocks and was looking at a Niagara 1200 as power conditioner for the rest.... any tips greatly appreciated!
Technics SL1200M3D
Tonearm: Jelco 750D
External PSU: Paul Hynes SR4
+
Cart: Nagaoka MP150
Type: Moving Iron
Output voltage: 1kHz, 5cm/sec:4.5mV
Frequency range: 20-20kHz
Material: diamond, nude
Stylus type: elliptical 0.4 x 0.7 mil
Tracking force range: 1.5–2g
Tracking force, recommended: 1.8g
Recommended load capacitance: 150-200pF
>>
Phono Stage: RCM Sensor 2
Input: RCA – Balanced and Unbalanced (selectable via switch)
Output: Balanced XLR / Unbalanced (single ended)
Input sensitivity: 0.3–5mV (selectable in 7 steps)
Gain: 52–76dB (2 VRMS output at 1 kHz)
Input impedance: 20–47kΩ (selectable in 8 steps)
Input capacitance: 150 pF
THD: 0,01% (1kHz)
RIAA linearity: +/-0,3dB (20Hz–20kHz)
Nominal output: 2V rms
Max. output level: 8V rms
Output impedance: 70 ohm
S/N: 85dB (lowest gain settings)
RIAA linearity: +/- 0,3dB (20Hz–20kHz)
>>
Cello Palette Preamplifier
Maximum output: 8V RMS (single-ended), 16V RMS (balanced)
Line Gain (Switchable): 0dB, 6dB, 9dB, 12dB, 18dB
THD (ref. 6V): 0.084%
Input impedance (Unbalanced): 1MΩ
Output Impedance: 150Ω
Running Balanced into >>
Pass Labs Aleph 2 (Monoblocks)
Topology: Class A, single-ended
Power Output: 100W into 8Ω / 200W into 4Ω
Maximum Output: 10A, 40V (Peak)
Gain (Balanced): 20dB
Gain (Unbalanced): 20dB
Gain (Unbalanced, XLR Jumpered): 26dB
Distortion (100W, 8Ω, 20Hz-20kHz): 0.5%
Input Impedance (Balanced): 25kΩ
Input Impedance (Unbalanced): 10kΩ
Output Impedance: 0.1Ω
Damping Factor: 100
Common Mode Rejection: 60dB
Power Consumption: 300w
Output Noise: 600μV
DC Offset: <100mV
>>
A/D/S L1290 Loudspeakers
Frequency responce: 40hz–27khz,
Impedance: 8Ω nominal
Efficiency: 90dB SPL from 2.8 VRMS (1W)
Crossovers: 500hz and 5khz, 12dB/Octave slopes
I've had way too much free time and gone down a few rabbit holes purchasing some older gear, some of which I've got a little experience with and some none... but was curious, because I am not the best technically, if any of the more seasoned audiophiles might have any advice regarding my chain. I'm replacing my 30w Pioneer receiver with separates (put all my specs in the below list) – I got the preamp as a family hand-me-down and I've just bought the monoblocks (having service done now) so I've not heard it all together yet. The player and speakers I've been using forever. But will I OK in terms of matching impedances, gain, etc? Oh, and I'm installing a dedicated line for the monoblocks and was looking at a Niagara 1200 as power conditioner for the rest.... any tips greatly appreciated!
Technics SL1200M3D
Tonearm: Jelco 750D
External PSU: Paul Hynes SR4
+
Cart: Nagaoka MP150
Type: Moving Iron
Output voltage: 1kHz, 5cm/sec:4.5mV
Frequency range: 20-20kHz
Material: diamond, nude
Stylus type: elliptical 0.4 x 0.7 mil
Tracking force range: 1.5–2g
Tracking force, recommended: 1.8g
Recommended load capacitance: 150-200pF
>>
Phono Stage: RCM Sensor 2
Input: RCA – Balanced and Unbalanced (selectable via switch)
Output: Balanced XLR / Unbalanced (single ended)
Input sensitivity: 0.3–5mV (selectable in 7 steps)
Gain: 52–76dB (2 VRMS output at 1 kHz)
Input impedance: 20–47kΩ (selectable in 8 steps)
Input capacitance: 150 pF
THD: 0,01% (1kHz)
RIAA linearity: +/-0,3dB (20Hz–20kHz)
Nominal output: 2V rms
Max. output level: 8V rms
Output impedance: 70 ohm
S/N: 85dB (lowest gain settings)
RIAA linearity: +/- 0,3dB (20Hz–20kHz)
>>
Cello Palette Preamplifier
Maximum output: 8V RMS (single-ended), 16V RMS (balanced)
Line Gain (Switchable): 0dB, 6dB, 9dB, 12dB, 18dB
THD (ref. 6V): 0.084%
Input impedance (Unbalanced): 1MΩ
Output Impedance: 150Ω
Running Balanced into >>
Pass Labs Aleph 2 (Monoblocks)
Topology: Class A, single-ended
Power Output: 100W into 8Ω / 200W into 4Ω
Maximum Output: 10A, 40V (Peak)
Gain (Balanced): 20dB
Gain (Unbalanced): 20dB
Gain (Unbalanced, XLR Jumpered): 26dB
Distortion (100W, 8Ω, 20Hz-20kHz): 0.5%
Input Impedance (Balanced): 25kΩ
Input Impedance (Unbalanced): 10kΩ
Output Impedance: 0.1Ω
Damping Factor: 100
Common Mode Rejection: 60dB
Power Consumption: 300w
Output Noise: 600μV
DC Offset: <100mV
>>
A/D/S L1290 Loudspeakers
Frequency responce: 40hz–27khz,
Impedance: 8Ω nominal
Efficiency: 90dB SPL from 2.8 VRMS (1W)
Crossovers: 500hz and 5khz, 12dB/Octave slopes
- ...
- 35 posts total
- 35 posts total