2. speakers
  3. 158611-148323

Just starting out and need advise for sub woofer connection

Hi I’m a rookie you guys are the big leagues so I am asking for your help.
I recently purchased a Canton K9 bookshelf speaker and stands. This speaker has a set of speaker cable posts for high and midrange and another set for the bass with jumper bars attached to the two sets of posts. Adrian the seller was so kind to include a Jamo c80 sub in my purchase. Which I hooked up as Paul McGowan the PS Audio poobah suggested by running speaker cable from my amp to the c80 cable posts for both left and right channels. Given this set up since both my main Cantons and the sub are receiving bass frequencies and both are playing them, this seems to be a duplication of effort and seems wrong. I was wondering could I, should I remove the jumper cable from my Cantons and attach my speaker cable to the terminals marked high and midrange? I assume doing so stops my Canton drivers from having to play bass frequencies. That Would free up these speakers from bass responsibilities? Is that a good thing? Should I do this ? and what must I be mindful about if I do this? Do I have to do anything to my subs crossover a knob reflects 40HZ to 200HZ  The canton literature mention a cross over at 3000 hz which to me woulld mean at the very least the difference between 200HZ and 3000 hz would be lost or should I forgetabout using the sub? The c80 also has what look to be RCA connectors titled Line left and right in and left and right out. Finally there is a LFE connection which is the same as the RCA left in. Thank you in advance for your help. Regards Scott
scott22
bkeske's avatar
bkeske
5,597 posts
 
The C80 Manual does not state hooking up the sub via the ‘main outs’, but the pre/integrated ‘sub outs’ or LFE. Or, via the high level speaker terminals, which I would recommend, personally. The last thing I would do is use LFE for music. Home theater? maybe, but that’s a whole nuther can of worms.
fuzztone's avatar
fuzztone
5,635 posts
 
Does the sub have line in?
I can not tell, I can find no photos. If so, you amp setup is all important. I've added RCA's tapped to the volume pot on an ntegrated before.
More info necessary to remediate.
bkeske's avatar
bkeske
5,597 posts
 
Yes, the sub has both R&L line-in or LFE using the left channel. The manual is clear. It also has RCA outs to ‘daisy chain’ to a second sub.

Or, simply use the high level speaker terminals with an extra set of cables from the amps terminals feeding both the Cantons and Jamo. easy peazy.
scott22 OP
266 posts
 
First let me thank all of you for your kind responses. .Bkeske   a special thanks for your detailed response and guidance which also reaffirming my belief.  Jamo manuals are less than adequate.   I will reset my  Jamo sub to 40 hz.and go from there. I currently set it at 80hz, I believe as again  Jamo does not provide much guidance the knob that controls the frequency has  40 hz at one extreme and 200 Hz at the other then dots which mark off some number but not in equal amounts like say 20 hz increments. Currently, the Jamo does disappear my wife would like all of it to and often me with it lol. By the way my the Cantons have a wonderfully detailed sound not at all fatiguing but oh so revealing at lest to my old and inexperienced ears.  Thanks again    
bkeske's avatar
bkeske
5,597 posts
 
@scott22 

Yep you just have to play around with it. Sub positioning and adjustments in terms of cut-off and gain is not an exact science, as again, every room is different, and also the speakers you are 'marrying' them to. 

As your Canton's dive down pretty deep, I would not think you want the Jamo set much higher than 60, and I'm just guessing, but lower is probably better. But again, gain and placement all come into play. 

Im sure your wife would want them to disappear ;-) So, you may be more limited in it's placement. Just do the best you can, and try a variety of different things. Believe me, this could take a while, so be patient. 

Also, for music, don't discount the feeling that the sub itself is not doing much. That can be a good thing, and turn it off, listen, then back on to see differences it may actually be making. Pick a good wide range dynamic selection.
More to discover