Duelund conversion to DIY Helix Geometry Cabling

@lionel  just found Ice Power Module details - in the literature that is available online- 

The speaker output of the 200AS1 is a balanced output with two active signal lines capable of driving complex speaker loads. As the speaker output is already in a balanced configuration, bridging of two channels is not possible.

So I can confirm the Helix Cables WILL NOT sound their best with this amp

Regards - Steve

Steve, 

Not meaning to split hairs, the ICE module referred to is the 1200AS  (or 1200AS2 if a stereo amp).  I'm sure they are configured the same way.

As far as you are aware, is this compatibility concern related to the speaker cable only?

Thanks 

@maxuima95 - YES - only for the speaker cable !

Here is my understanding (and I am paraphrasing heavily here)...

• the "balanced" audio signal that comes through an XLR Interconnect (e.g. from a DAC) is "processed" by the receiving component (e.g. a pre-amp) such that any noise is removed, resulting in a single audio signal (not two)
• If the pre-amp has XLR outputs the "clean" audio signal is again "processed" into two signals 180 degrees out of phase, but there needs to be a neutral to complete the circuit
• Now in a Balanced "symmetrical" amp design, the signal comping into the XLR input is processed in the same manner as the pre-amp processed it’s XLR input
• but in the output stage of the amp a principle similar to a balanced power supply is employed, in that two signals that are 180 degrees out of phase is used to drive the speaker - BUT there is NO neutral at the output
• so if you were the speaker - the signal in one wire will effectively "pull" the voice coil and the signal in the other wire will effectively "push" the voice coil and vice versa as the signal moves from the +ve cycle to the -ve cycle.
  
• So what happens if the HELIX SPEAKER CABLES are used to connect the speaker to this type of amp - the UP-OCC Signal wire has excellent transmission capability, but the neutral cable being 2.5 times longer and only silver plated copper, does not conduct it’s 180 degree out of phase signal quite as "accurately" as the signal wire does
• This results in imperfect forces being applied to the voice coil and clarity, tone, imaging dynamics are impacted and the resulting sound is not as good as it could be
• However - the amp WILL NOT suffer any damage as a result of the Helix cables being connected.

I hope that explains things :-)

Regards - Steve

OK, so in my post on 01-20-2021 6:13pm (on page 6) I talked about removing the insulation from the Neotech and VH Audio wires for the signal wires of my interconnects. I said at the end of the post that I would provide an update on the burn-in process - this is IT :-)

So today, I was only planning on listening casually and I had not listened to an album by Colin Blunstone for a while, so I pulled it out of its sleeve and plonked it on the turntable..

As the "needle dropped" the sound was breathtaking. I had never heard details or imaging antwhere near as good as this - EVER !!!

So after listening to the album, I thought what about the digital rig - is that gonna be as good???
- it has identical cables made around the same time and had a little more burn-in under it’s belt

Since I subscribe to Amazon Prime, I searched for Colin Blunstone and as it turns out they had a few tracks

Playing those tracks simply confirmed that my digital rig was very close to my analogue rig and provided the same spacious and detailed sound.

Now I don’t know if burn-in is complete, but based on this performance - it’s a good way into the process and sounding pretty amazing.

I remember the very first pair of Helix Speaker cables I made - they had a similar impact - a sort of "What The Heck" response.

Today was yet another WTH day, and in between there has been many moments where the improvements were discernable but not quite in the same league as this one.

Up to this point, I was not planning on upgrading my web site with this version of the Helix simply because of the possibility of the bare wires oxidizing and possibly forcing a rewire a few years down the road.

But the impact of this change warrants publication on my web site for all to enjoy AND from my current observations of how well the bare wire seems to be holding up I think that publication is a must.

The sound my system is producing is amazing me more everyday - i have NEVER heard anything this good and I have listened to systems upwards of $300k with over 30k in cables alone. By comparison my system MSRP is around 17k including cables and stand.

I can only imagine the sound some other members must be getting from their systems :-)

Now the only thing left...

• I used to use a version number to denote a new release - like MK I, MK II,etc...
• with the latest version I changed from a version number to a new name - The Helix IMAGE, because of its outstanding imaging
• so, do I call this one - The Naked Helix? or Helix au Naturel? or ???

Time will tell :-)

FYI - I have adopted the bare wire inside a Teflon (or PVC) tube approach on ALL my cables. For the signal or live wires I use

• 1 x 12 gauge Neotech UP-OCC copper on power cables
• 1 x 14 gauge Neotech UP-OCC copper on speaker cables
• 2 x 18 gauge Neotech AND VH Audio UP-OCC copper wire on the interconnects
• The neutral remains Silver plated stranded Mil-Spec wire
• I am toying with a 2 x 14 gauge Neotech UP-OCC live conductor for a power cable - still contemplating this one

If you haven’t tried the Helix using the bare wire inside a Teflon tube approach - give it a whirl - you WILL NOT regret it.

It is a significant improvement, with absolutely stunning results

Regards - Steve

@williewonka 

Have you tried a Naked Solid Silver cable yet? Do you think you would need to replace the wire down the road?