Moderately priced DIN phono cable suggestions needed

OP: Take Five Audio's Mogami phono cables are worth taking a look at. Gene's builds are on par with high end cable makers that charge considerably  more money than what he is charging, he list specs for his finished cables, and is always a pleasure to deal with.

@noromance, Jelco from my understanding used Mogami cable in their tonearms and cables, as do a few high end cable makers according to other posters.

Thanks all,
@noromance The turntable is in an enclosed rack right now and I was hoping not to have to remove it until I have the new cable and am ready to install it. I hoped someone here might have knowledge of the PT-5 tonearm and which DIN pattern it has.
@krameshmurthy Thanks for the tip on the Zafino junction box, will look into that.
@jeffrey75 I looked up the Take Five 2893 DIN to rca phono cable, looks very good. About the same price as the Audio Sensibility.

Caution,

some tonearms need LONG din connectors, small diameter barrel,

https://www.google.com/shopping/product/1?q=long+narrow+din+connector&bih=648&biw=1280&r...

to get in/up high enough in a narrow tonearm tube to connect. I would definitely check with tonearm manufacturer first, or, take it out of the rack, see for yourself.

i.e., this connector’s short shoulder design would not get thru the arm high enough

https://www.google.com/shopping/product/1?q=high+quality+5+pin+din+&bih=648&biw=1280&rlz=1C1SQJL_enUS881US881&hl=en&sxsrf=ALeKk02SRrW9K8eYVKtCQh8CHa8Uvo_4iA:1618327684935&oq=high+quality+5+pin+din+&gs_lcp=Cgtwcm9kdWN0cy1jYxAMMgQIIxAnMgUIIRCrAjIFCCEQqwIyBQghEKABMgUIIRCgAToECAAQQzoKCAAQsQMQgwEQQzoICAAQsQMQgwE6AggAOgQIABAYOggIABAWEB4QGFDjcVj_zwFg8ZwCaABwAHgAgAFziAGaDpIBBDIxLjKYAQCgAQHAAQE&sclient=products-cc&prds=eto:12667615546723987542_0,pid:12667615546723987542&sa=X&ved=0ahUKEwjRiKWWxfvvAhXiQ98KHXlfA8kQgwgItQU

I got this one, (scroll down, see RCA-5P version) based on my Blackbird Tonearm Maker’s recommendation. I think a bit over your budget, the point is, it fit the Blackbirds short tube, but the straight din end would not get up my Acos tonearm’s long tube.

https://www.ortofon.com/6nx-tsw-1010-p-414?variant=J061210048

Also, do you know the clearance from the bottom of the tube to the bottom of the Tt's feet? You might want/need a right angle version as I did with my Mission arm.

I ended up asking these people to make me a special: an rca/din cable using the long narrow din connector.

https://www.ebay.com/itm/Custom-Length-Audiophile-Turntable-Phono-RCA-Cables-w-Ground-Wire-Quad-Brai...

Very cooperative, just write and ask, I think mine sounds as good as the much more expensive Ortofon. Pick your color and length.

Even if any connector, fat, right angle ... will fit a short tube, you might want to ask for a price.

I spoke with Gene from Take Five.  He was super helpful and explained a lot of things I didn't know about tonearm cables.  He says his cable is very flexible, so that's good.  I can't seem to get hold of Vinyl Nirvana, but their site now shows to have one of their cables in stock.