2. analog
  3. 150758-92835

Trans-Fi Terminator Tonearm: 2019 Update

In reading a few related posts on linear tracking tonearm, in general,  and Trans-Fi Terminator , in particular, I thought I would give a brief update of the Terminator.

I purchased the arm directly from Andrey in Moscow two months ago. From what I understand, Andrey has taken over production after Vic's retirement. What I received is the most up-to-date version of the arm with the carbon fibre wand and brass counterweights, the direct wire leads from cartridge to  phono amp, and a new brass manifold ( not evident from the main web-site). Both the wand and the new manifold are Andrey's contribution to the continued refinement of the Terminator.

Also,  please visit this site: https://darklanternforowen.wordpress.com/2017/04/15/terminator-tonearm-new-arm-mount/. This gentlemen from NZ has developed a new arm mount for the Terminator which advanced the arm's sonics even further. It was reading through the the development of this new arm mount that convinced me to order the Terminator after much prior research. I did not purchase the arm mount from NZ as it would not readily fit my Verdier La Platine, instead Andrey made a custom arm mount. It is in essence a two point support mount rather than a single point support rod that is commonly used. 

My previous arm was a SME V of 1990's vintage mounted with a ZYX airy. The Terminator is several notch above the SME V. All the accolades given to the Terminator seem justified. My main point in writing is that the new developments by Andrey, i.e. the carbon fibre wand and the newest brass manifold, seem to improve upon the Terminator even more ( see link above ). This is the news that I wanted to share with existing Terminator owners. I asked Andrey to start a blog on all the new stuff that is happening with the arm, but it seems that he is busy making 'things'!




ledoux1238
ledoux1238 OP
280 posts
 
Don,

The darker blue containers, seems like 20 litre, are surge tanks? There are two connected next to each other, and a third next to the turntable? 

You're getting a 6 psi reading out of the pump. Do you have a pressure gauge before the tonearm? I am particularly interested in what  the actual pressure reading at the tonearm. While I have a much more rudimentary pump / tank system, I am thinking of installing a gauge between all the surge tanks and the tonearm. The actual pressure to the tonearm should be much lower. If I am not mistaken, @terry9 has his arm set at 0.5 psi. J
terry9
2,333 posts
 
Actually, the Pz wand prefers 0.3 psi.

Overkill? Overkill? What is this word? Sounds like blasphemy to me ...
redcars
11 posts
 
@ ledoux1238  
Pump > filter > bleed valve > regulator + gage > two 5 gallon tanks > 30 feet of 1/2 inch ID hose > 2 gallon tank > tonearm.  I don't have another gage at the tonearm.  Maybe I'll add one at some point. I can understand why you are asking, but the only purpose would be to compare tonearm readings with others.  With a regulator, it does not really matter.  It's whatever sounds best to you.

Best,
Don
redcars
11 posts
 
0.3 psi at the regulator sounded great tonight.  Arm pressure must be very close or the same as this.

Best,
Don
ledoux1238 OP
280 posts
 
Don,

With the additonal surge tanks, valve, filters,...etc, I had assume that there would be a drop in pressure at the arm. But as you say, it's the sound that matters. I think someone, maybe Terry (?), commented that music sounds livlier at higher pressure. On my previous lighter cartridge, I could almost confirm that. 

It's interesting that you have arrived at the same pressue as Terry with the Panzererholz wand, given what I assume are two very different setups. There probably is a pressure range within which the Termintor is comfortable in.

With the ET arm, the range is ( according to Bruce on his web-site ) 3 - 10 psi depending on the pump used, it being a high pressure arm. It is ten times the pressure range that you are experiencing. And apparently at that range, condensation becomes an issue. Living in a very humid environment, I opt for a low flow / pressure arm to avoid the very real  potential for condensation. 
More to discover