Duelund conversion to DIY Helix Geometry Cabling


I have been an avid user of the Duelund cabling for over two years now and have used them exclusively in my system with great results. I have built many for friends and have used a full loom of interconnects, speaker cables, power cords and an extensive wiring modification for a previously owned balanced power conditioner utilizing Duelund 600V PolyCast wiring which was transformative. My cabling desires can be a little addictive as I have owned and evaluated 40+ brands of cabling costing more than an entire stereo system!

Over the past six months I stumbled upon a thread here on Audiogon in regards to a Helix designed cabling and as you probably already know, I just had to look a little deeper into this cable design…After a month of studying and sourcing parts, I decided to reach out to the designer/architect, Williewonka who gave more insights and philosophy on how the cable came into existence.

That conversation got the ball rolling in converting one of my KLE Duelund interconnects to Steve’s Helix designed which only entailed replacing the neutral with a Mil-Spec 16 AWG silver-plated copper wire with the neural wire being 3 times longer than the signal wire and of course the “Coiling” of the neutral wire : )

After the modification was complete, I was not sure what to expect from the Helix cabling but I was quite shocked with the results with “ZERO” burn-in time…The sound stage became much wider/deeper with a much tighter/focused image and clarity/transparency is like nothing I have ever heard in any cabling regardless of cost. In fact, I just sold a full loom of a commercially designed Helix Cable that’s renowned around the world and has more direct sale than any cable manufacturer; these $200 DIY Helix Cables walked all over them…

I believe you will hear the same results as I have and have heard back from friends who have already modified their Duelunds with the same results; WOW! Remember the cables will need 200+ hours to burn-in and settle into your system. My system is now 90% DIY Helix to include IC, SC, PC and Coax with each cabling adding its beauty of an organic and natural presentation that draws you into the fabric of the music.

You can tailor the sound of your cables using Duelund, Mundorf silver/1% gold, the outstanding Vh Audio OCC Solid Copper or Silver with Airlok Insulation or your favorite wiring and you can change it at any time…

 

http://www.image99.net/blog/files/category-diy-cables.html

https://forum.audiogon.com/discussions/difference-in-sound-between-copper-and-silver-digital-cables

https://forum.audiogon.com/discussions/adding-shielding-to-existing-cables

 

Enjoy,

Wig


128x128wig
On a different note - regarding interconnects.
The observations found by you, Steve, indicates that there are huge improvements to be expected, if one replaces mil spec with Neotech. I assume your observations are with single ended cables using RCA’s, so that cable will consist of a signal wire and a helix both made by using Neotech. My question is, what are the expectations, when interconnects are balanced using XLR connectors and where Neotech is used for ve+ and ve-. Would you expect differences for the better, if the helix (which is ground on a balanced cable) also was converted to Neotech?
@provst - WRT Which wire to use

This is a tough one - It’s too bad you have purchased the TFA Mil-Spec.

I could tell you that there was only a tiny improvement, but it was easily discernable and I considered it a worthwhile upgrade

Having said that the two cables I upgraded were
  • the PC for the amp
  • the PC for the power distribution box that provides power to the source components
  • the two cables from the distribution box to the source components still use the Mil-spec
So if oyu have a similar setup you could use some of the Mil-spec

Generally - I would recommend getting the Neotech Stranded UP-OCC wire and make a single Helix coil for the neutral with a 2 x 14 gauge live conductor using the Air adaption (i.e. bare wire inside teflon tube) for best performance.


RE:
I assume your observations are with single ended cables using RCA’s, so that cable will consist of a signal wire and a helix both made by using Neotech. My question is, what are the expectations, when interconnects are balanced using XLR connectors and where Neotech is used for ve+ and ve-. Would you expect differences for the better, if the helix (which is ground on a balanced cable) also was converted to Neotech?
Yes - a single ended cable was used
Yes - I would expect the same improvements for XLR with all wires being Neotech with a single Helix Coil neutral (i.e. ground)


Regards - Steve









@williewonka I have seen USB, but what about micro USB and type C? Also, what about coaxial Bnc cables? 
@provst 
@williewonka 

For Powercables that have two TFA Mil Spec Helix. Wouldn't you just use the two TFA 12g wire for the Ground and get a single 12g strand of Neotech for the Neutral?