Main vs. sub panel for dedicated lines

Ground the sub panel to the main which is grounded to earth. 

I would also recommend grounding the ground to ground, and then grounding the Earth to ground. You never can be too sure, so I would ground all the grounds to all the pipes as well. Because, like, they go into the ground. 

Yeah, I know what you're thinking. There he goes being a a-hole again. But no, this actually is code now. The difference between all this BS everyone is so intent on doing, and what actually works, is so obvious if you could hear it that would be the end of that. But you can't. It is way too much work. You never in your life will do it to compare and know. That's why I did it. To know. Then comes the reason I hardly ever bother posting on the subject, https://youtu.be/9FnO3igOkOk?t=39

millercarbon9,434 posts

06-03-2021
11:27pm

I would also recommend grounding the ground to ground, and then grounding the Earth to ground. You never can be too sure, so I would ground all the grounds to all the pipes as well. Because, like, they go into the ground.

Yeah, I know what you’re thinking. There he goes being a a-hole again. But no, this actually is code now. The difference between all this BS everyone is so intent on doing, and what actually works, is so obvious if you could hear it that would be the end of that. But you can’t. It is way too much work. You never in your life will do it to compare and know. That’s why I did it. To know. Then comes the reason I hardly ever bother posting on the subject, https://youtu.be/9FnO3igOkOk?t=39

MC, finally a post of yours that makes sense. :)

Broken down into simple English.
To earth ground a sub panel or not to earth ground a sub panel that is the question......
.

MC,
I was looking at your system thread and read this:

Stewart Marcantoni taught me it all begins at the wall. The System begins with 4 ga wire at the panel. This 4 ga brings 240v power to a step-down transformer located just beneath the system. Now at 120v, it is only about 5 ft from the Medusa power center. The step-down transformer and Medusa are both grounded to the same ground rod the same 5 feet from the system. Power wire is all cryogenically treated.

@ millercarbon ,

I have some questions if you don’t mind.

What size, (breaker handle rating), is the 2 pole breaker, at the main electrical panel, that feeds the primary winding of the isolation power transformer?

What size, VA rating, is the isolation power transformer?
Does the secondary have overcurrent protection? Are connected circuit(s) wiring protected?

Is the secondary, one winding, or two windings? In other words can the secondary be wired for 240/120V out or 120V out only?

Is the ground rod used to earth ground the new separately derived power system? Is one of the 120V secondary winding leads intentionally grounded making it the neutral, The Grounded Conductor?

Is the neutral conductor bonded to the transformer metal case/metal enclosure/ transformer Iron core? Are circuit EGC(s) (Equipment Grounding Conductor)(s) connected to this star equipment grounding point?

Is the ground rod bonded to the main electrical service "System Ground"/"Grounding Electrode System" with a minimum #6awg copper wire?

OR,
Are you floating the 120V secondary? (No reference to ground from either lead/leg of the 120V secondary of the xfmr? An Ungrounded Power System....
The ground rod is only connected to the 120V EGC(s) connected loads.
Ground rod is not connected to the main electrical service Grounding Electrode System.

FWIW
Fact.
Mother Earth does not possess some magical mystical power that sucks nasties from audio equipment.

Grounding myths from somebody that knows something about grounding.

Henry W Ott
Quote:

Grounding Myths

"Electromagnetic Compatibility Engineering" by Henry Ott

3.1.7 Grounding Myths

More myths exist relating to the field of grounding than any other area of electrical engineering. The more common of these are as follows:

1. The earth is a low-impedance path for ground current. False, the impedance of the earth is orders of magnitude greater than the impedance of a copper conductor.

2. The earth is an equipotential. False, this is clearly not true by the result of (1 above).

3. The impedance of a conductor is determined by its resistance. False, what happened to the concept of inductive reactance?

4. To operate with low noise, a circuit or system must be connected to an earth ground. False, because airplanes, satellites, cars and battery powered laptop computers all operate fine without a ground connection. As a mater of fact, an earth ground is more likely to be the cause of noise problem. More electronic system noise problems are resolved by removing (or isolating) a circuit from earth ground than by connecting it to earth ground.

5. To reduce noise, an electronic system should be connected to a separate “quiet ground” by using a separate, isolated ground rod. False, in addition to being untrue, this approach is dangerous and violates the requirements of the NEC (electrical code/rules).

6. An earth ground is unidirectional, with current only flowing into the ground. False, because current must flow in loops, any current that flows into the ground must also flow out of the ground somewhere else.

7. An isolated AC power receptacle is not grounded. False, the term “isolated” refers only to the method by which a receptacle is grounded, not if it is grounded.

8. A system designer can name ground conductors by the type of the current that they should carry (i.e., signal, power, lightning, digital, analog, quiet, noisy, etc.), and the electrons will comply and only flow in the appropriately designated conductors. Obviously false."

Henry W. Ott

Who is Henry W Ott?
http://www.hottconsultants.com/bio.html

.

Run the lines from your properly grounded sub panel and be done with it. Buy hospital grade plugs.
I think I ran 10 gauge. So long ago I don’t remember.
I did put in a new grounding rod and a more robust grounding strap when I ran the dedicated lines. I believe the wire from the pole to my main in the garage is aluminum? I know the wire from the main to my sub is aluminum.
It is current no more no less. Stable Hz is as important as anything when it comes to electronics.
Depending on where you live line voltage could be anywhere from 114v - 120v. 
But I’ve been in many an industrial plant that had 208v lines.