Current deals to good to pass up!

My main system's speakers are new wood enclosures with vintage electro-voice drivers (horns and 15" woofer), crossovers, L-Pads from a Fisher President II Console made in 1958. The drivers in the horns are impregnated fabric, they last indefinitely, the woofers can be re-coned, the L-Pads can be replaced. Replacement horns and woofers can be acquired. 

electro-Voice Model Six was amazing, and unique, it incorporated 5 separate sound profiles via a resistor based attenuator circuit, horns, and an 18" woofer.

https://products.electrovoice.com/binary/E-V%20Six%20EDS.pdf

Two pairs, local pickup only are on eBay

pennsylvania

https://www.ebay.com/itm/154513478054

indiana

https://www.ebay.com/itm/363294554414

I am tempted every day by the ones near me.

Nearly New, good savings

Rothwell SUT, MC1, 220 Euros, or $262. usd plus shipping from Ireland (ask for price). New: $280 euro, $333. usd. Seller says a few months old.

https://www.adverts.ie/home-audio/rothwell-mc1-sut/23521441

http://www.rothwellaudioproducts.co.uk/html/moving_coil_step-up_transforme.html

I just happen to be looking for a SUT for my friend’s MC cartridge.

By design, this SUT 12.9 x-factor shows 100 ohms loaded impedance to the MC Cartridge. For many cartridges, fixed 100 ohm load can be an advantage. (typical 12.9 x-factor shows 283 ohms to the cartridge).

Rothwell says for cartridges with .3 to .7 mv signal strength; for coil impedance less than 20 ohms. 100 ohms is the ’ 10x formula’ of a coil with 10 ohms.

i.e. my friend’s Goldring Eroica LX .5mv signal, 8 ohm coil resistance. Goldring recommends 100 ohm loading. .5mv x 12.9 x-factor = 6.45 mV signal to MM input (allow for a small amount of signal strength loss).

i.e. my AT33ptg/II .3mv, 10 ohm coil impedance. only 3.87 mV signal; formula’s 100 ohm load. A bit low signal strength for me, I use my SUT’s 20.68 x-factor: 6.02 mV which shows 110 ohms to my 10 ohm cartridge.

Note: no MM Bypass; single input, it’s a specific solution which keeps the cost down.

This Entre ET-100 has 3 inputs, MM Pass, and 3 optional settings

https://www.ebay.com/itm/203344578296?mkevt=1&mkcid=1&mkrid=711-53200-19255-0&campid=533...

I chose this one, Fidelity Research FRT-4: 3 inputs, MM Bypass; 4 optional settings

https://www.ebay.com/itm/124558472024?hash=item1d00437358:g:QO4AAOSw5RVgmR1y

My Voxativ’s come next week @ 2G’s, Best 2k i ever spent in this hobby.
Best bang for the buck. You know its hard trying to find a great deal in this hobby,
But I think I found one.

Denon SUT for two arms, 2 settings, and MM Pass, $230. or offer

https://www.ebay.com/itm/284336229896?epid=1856965640&hash=item4233c28e08:g:Eh0AAOSwgeVgytcz

https://www.ebay.com/itm/184923398400?mkevt=1&mkcid=1&mkrid=711-53200-19255-0&campid=533...

40 ohm setting

for any cartridge with coil impedance 40 or less. designed specifically for Denon Cartridges DL 103 and DL 103s
1:10 x-factor, +26db
................................................

3 ohm setting

for any cartridge with coil impedance 3 or less
(compared to others, probably 1:36 x-factor, +31 db, verify)

I just noticed this was in the 'speakers' category, sorry.