Rechecking Cartridge Alignment


Had my Ortofon Cadenza Bronze installed 3 years ago and it has approximately 800 hours of playing time. Run it on a VPI Prime.

Question: When does it make sense, if at all, to have the alignment rechecked professionally?  I am not hearing anything problematic, but don't know what I don't know.

dsockel

Define "professionally".  Do you have a decent protractor, stylus force gauge, and etc, that you once used to align this cartridge?  If so, just do it again. Your work is bound to be as meticulous as anyone else's in your immediate vicinity, because you probably care more about it.  If you want to spend $500 to have your cartridge fully evaluated by Wally Tools, that's another matter.

Now, and you might want to have the stylus inspected properly via stylus microscope. Nearby dealer? They want to sell you something? Hard to trust. I send my AT MC to AT, trust them to give me trustworthy response. I tried one of the toy usb microscopes, a waste of time IMO.

Meanwhile, I re-check tracking force and anti-skate often, perhaps monthly, and before any pre-planned listening session with friends. Miniscule particles on the bearings might/can alter fine adjustments. Miniscule changes to level (rubber compression, ??? very slight changes can occur that effect anti-skate to a minor degree, but worth checking.

Alignment: I have an LP with all the lines to easily double check null points, correct means you got the screws tight enough, thus overhang would have remained correct.

Azimuth: fixed cartridges, they always reflect straight, but reassurance is a good thing

Azimuth: removable headshell, I check every time I remove/replace/change the headshell. Mirror technique, pretty easy to see any error in the reflection in the mirror..

VTA is the trickiest, especially if you change to headshell with a different cartridge height. My removable headshell arm allows easy/instant VTA adjustment, I don’t go for perfection by listening, simply arm parallel while playing, sounds great, done.

Avoiding ’wrong’ more important to me than audible perfection. The cartridge’s specified VTA, i.e. shure 15 degrees, Ortofon 20 degrees are for when the cartridge is down in the groove with tracking force applied. I have a transparent protractor with degree lines scratched longer to see ’better’, but I find parallel arm is always close to my best protractor ’guess it’s right’.

I believe any/every one who is involved with LP should acquire the inexpensive tools and skills to mount/align cartridges themselves.

Stylus Life is subject to many factors, and ....

Here's a response in a Ortofon Stylus Life Discussion:

 

"HI All,
I have been tracking stylus wear using a stylus microscope for 30 years. I have run two different hi fi repair shops for a total of 13 years. I would examine every stylus that came into my shops under a Shure SEK-2 purpose designed microscope.This amounts to thousands of styli. Of course, I have examined my own styli as well.

I have found that around 1000 hours is the usual life time for a stylus. It varies a little but not much. Remember a diamond is a diamond. And a groove is a groove. There are not many variables here, VTF being the primary one. But VTF does not seem to make much of a difference mostly because most cartridges are at their best within a fairly narrow range of VTF's.

I have also found that most owners are wildly optimistic about the number of hours on their stylus.

Do not kid yourselves. Don't make the mistake of over using your stylus. It WILL tear up your records.

Wear can be detected by ear. It first shows up as mistracking in the inner grooves on the left channel on highly modulated passages where you never heard distortion before. As the wear progresses distortion will become more common until you can no longer ignore it. This may be too late for your records.

Since many other things can cause mistracking, a microscope is invaluable for detecting that the problem is actually stylus wear and not a set up problem. This and you can actually see the degree of wear. Do not mistake this as a simple magnifier. It's a serious instrument that you can observe stylus wear facets at 200X.

For those that wish the best for your records you should have a stylus microscope. Unfortunately, today they are rare and hard to find. The most common one was the Shure SEK-2 but good luck finding one. I have one but it's not for sale.

Because of the availability issue, I designed a substitute using a laboratory microscope that anybody can build. I posted this project on Audio Karma. Here is a link to the build article:

http://www.audiokarma.org/forums/showthread.php?t=225960

Check it out. You may need to build one. It's easy, sort of. I can't be without a good stylus microscope.

Sparky"

discussion

https://www.whatsbestforum.com/threads/all-ortofon-cartridges-have-a-600-1000-hr-stylus-lifetime.5672/#post-86400

.................................

another

 

"From their newsletter:
 

We have recently observed a number of discussions about stylus life time on HiFi forums. We have therefore decided to bring clearance in this matter and come with Ortofon official response:​

With proper care we find that up to 1000 hours is possible without degradation of performance. The stylus does begin to exhibit changes after 1.000 hours, but the stylus life as a whole is expected to top 2.000 hours.

Proper care comprises the following:

1. Cleaning of record by means of carbon fibre brush before and after every use. Cleaning of record by using record cleaning machine once in a while. 

2. Cleaning of stylus by means of a fine antistatic brush. Please remember to remove dust from the diamond tip before and after playback of each record.

3. Proper adjustment of antiskating, azimuth and tracking force"

discussion:

 

https://www.whatsbestforum.com/threads/new-ortofon-claim-on-stylus-life-expectancy.6018/