Comparison of sonic qualities of some tonearms

@whart … for rock solid machining quality assurace, definitely trust Kuzma…. 

I have been instrumental in encouraging a design to be produced for a removable headshell, that has the intent to surpass a Typical SME Bayonet connection.

The design selected is a little more involved when a Cart' remounted to a Headshell is to be exchanged. 

If mounting a Cart' on an alternate material or weight headshell, this process will be quite similar to the previous design.

The New Design is based on two interfaces both being interference fit, which as a end result creates a coupling that is substantially more rigid. 

Both the New and the old have been given a lot of time to be A/B compared, using same TT >TA >Cart'>System.

The outcome has proved to be one where the new design is as a end performance, one that is more than the sum of Parts used.

My assessment on the day, but realistically fair, when a Styli / Cantilever is concerned, has been that the typical design, has headshell functioning as a flag on the end of a flagpole.

I am a advocate of removable headshell, I now know the removable headshell design worthwhile aspiring to. 

During the design stages for a new design tonearm, I have been party to. I was quite encouraging in having a removable headshell design to be adopted that is quite different from the typical seen versions.

This not so commonly seen design for a removable headshell is now realised and in my recommended material. 

@whart ...creating a Vestico! *kazoo fanfare*  😏 *L*

There's other tales of woe & whoa in moddin' SLs'....

Anytime one ventures into the arm/carriage of them, you encounter the 'switch' that triggers the arm movement.  Although calling 3 hair-fine stiff wires a 'switch' is being kind, since it's basically a naked miniscule SPDT reduced to literally a 'hair trigger' that ought to have been left in a car bomb.

Been there...(no, not a bomb...this post wouldn't exist) ... have some options in mind when I must abandon sense and resort to mere 'high' hopes....

@lewm The problem with the weight on a string AS mechanisms is that records are hardly ever perfectly concentric. Now the cantilever has to over come the stiction. I recall the old days with a V15 in an SME 3009. I use to watch the cantilever wag back and forth on eccentric records. If I defeated the AS the wagging stopped and the cantilever deflected towards the right channel. You can't win. You envision magnetic AS correctly. In the case of the Schroder CB one magnet is fixed to the horizontal bearing and the other on an adjusting screw. The neodymium magnets have opposite poles facing each other so they attract. When you study the geometry of the situation, the distance at the pivot really does not change that much as the tonearm travels over the record's playing surface.  If the AS is set at the center of the playing surface, so the variation to either side is only a few mm at the magnets, well within neodymium range. Yes, there is a slight variation across the record, the AS force dropping as the arm travels across the record. AS is a ball park situation and the CB's AS stays well within the ball park and I have measured this with the Wallyskater which can be adjusted to measure the AS anywhere on the record. It changes less than 1%, probably less than the pivoted style AS mechanisms like the Kuzma. 

@tomic601 my wife tells me I'm 1000% dog. I started painting my nose black back in 95 to get more attention. Growing a tail helped.

@asvjerry See, that tonearm has warped your brain. I had that H-K turntable and it warped mine. Tail wagging the dog. There you go, best use of a Rabco, as a car bomb. 

@billstevenson I can't imagine rewiring an arm would bother you that much.

@whart The Koetsu works reasonably well in the Airline because of it's very low compliance. The air bearing does absolutely nothing to alleviate the high horizontal mass, that would be magic. 

Frank Kuzma does one of everything to suite all comers or just to say he can. His unipivots are just as bad or as good as anyone's and the same holds true of the Airline. He can not even make his mind up on what kind of turntable to build, so he builds one of everything.

@pindac Removable head shells are for lazy people. It adds another set of contacts which is never a good idea. I like the Kuzma/Schroder solution which is a removable cartridge carrier without another set of contacts.