New expensive power cord for amp and no change in sound?

I think you need to find a new alchemist.

Or a periodic table.

With my "Engineer" brain, I never believed any of this stuff about power cords sounding better/worse, or even different. Then, after chasing an intermittent problem/funny sound, for several months, in an Mc60, I became a believer. I had a cruddy power cord. Changing to a new "high current" cord, the problem immediately vanished and never returned in the 30 years I used that amp.

So yean. Power cords. Relevant.

"Maybe I’m ignorant, but why would a power chord make a difference to sound?"

- If you are a scientist an EE or an electrician, please risk that overwhelming temptation to try to figure that out. It just gets in the way of enjoying the sound of your system. All of us hear things differently and our brains process them differently, it makes us all unique and similar at the same time. If you try it and can’t hear a difference, fine. If you can’t fine too. Listen to eurorack!

     Back in March 2022: a thread about power cords and break/burn-in was started.

     I hate to type, so: I'm going to copy/paste some of my speculations.

     That a highly complex musical signal, MIGHT affect Poynting vectors and signal speeds*, in interconnects, in a much more profound manner than a simple AC (ie: a fixed 60/50 Hz) signal, in a PC, seems likely (at least) to me, as; in EVERY formula regarding *those two, a signal's frequency (frequencies) always factors in greatly.

     Further: the above and what I'll c/p (seems to me) lends credence to how the application of a stronger, DC voltage/field, outside a dielectric (ala Synergistic MPC and Audioquest DBS systems), might stabilize those vectors and signal speeds, PERHAPS eliminating some time smear and, "burn-in". 

rodman99999 5,456 posts 03-31-2022 at 12:13am    @holmz-       Bear with me a minute, in my folly, far as a possibility on why a power cord might make a difference.       Based on some of the theories on how electricity works, simplified:       The conductor acts as a waveguide for the signal/voltage.       Within the conductor: when excited by an AC current, electrons oscillate, generating photons/electromagnetic waves that travel, always from the source, to the load.        Keep in mind: all signals (ie: music, AC) are sinusoidal  waves        Those photons/electromagnetic waves travel through and outside the dielectric, which (according to it's permittivity/Poynting vectors) will have various effects on those waves.    One of the most obvious is the dielectric's effect on the speed of the signal.       The better designers of printed circuit boards, even take the above into account, when choosing materials for their products.        I posted a link on the first page that included data on the manufacture of semiconductor chips and what was observed when materials were cryo'd, during the process.     Short version: better contact/lowered resistance between layers.           Under the scanning microscope: much smoother surfaces observed.        I would hope, by now, it's a given that various cable constructions, twists, braids, etc, can make for a cleaner transmission of signals (ie: Litz, etc).                     Just seems to me (a hypothesis): given the above (some theories and some things established/measured/proven), it's not a big stretch to believe a power cord, built of the best conductor (ie: Ohno CC silver), wrapped in a very low dielectric coefficient dielectric (ie: Teflon), cryo'd for the smoothest transfer of those photons/magnetic waves and twisted in some crazy way, might not smooth out some of perturbations/noise, from the crap an AC waveform had to go through, back to it's generator.  (run-on, much?)        I haven't tested this, actually comparing two circuits, but: it wouldn't surprise me, if a power supply that used a choke, would be less affected by a better power cord, as the former can eliminate a lot of the high freq garbage, etc, that's either created by, or makes it through all the big converting/filtering stuff, in the power supply, before.        Never thought about PCs before the good stuff hit the market, but: the Physics/QED made sense.             I tried 'em, I like 'em and the science makes my head feel better.                               Don't care WHAT it does to anyone else's!

rodman99999 5,456 posts 03-31-2022 at 12:27am         OH, and: it takes some time for the dielectric to form, take a charge, polarize, or however one chooses to define the process, when a dielectric is subjected to electromagnetic waves, which affects the Poynting vectors, measurably/predictably.                                             The lower the material’s dielectric constant: the longer that takes.                                                               PC (interconnect/etc)  burn-in?    Maybe?

                                                                                         Happy listening! 

           For anyone ACTUALLY interested in doing some study, another rewind:

        Anyone needing a rationale for experimenting with new cables in their system and/or feeling dissuaded by the Church of Denyin'tology's antiquated electrical doctrines: take heart!

        Many new electrical facts have been established in the past 100 years, that support audible differences, between various cables, fuses, etc.

         I couldn't find anything like, "Updated Electrical Theory For Idiots", but- did manage to find something resembling a cartoon, that even a child could follow.  It neither mentions AC/sinusoidal waves in wires, nor does it go into the photon propagation of electromagnetic waves.   It does, however, emphasize/demonstrate how Electrical Theory has progressed, since the 1800s:

              (https://www.youtube.com/watch?v=KGJqykotjog)

        These next two presuppose a certain amount of knowledge, in the field of modern Electrical Theory.    Click, "more" in the first link's third answer, to get its entirety.    Note how it mentions the OLD, "... commonly held misconception that the flow of electricity through a wire resembles a tube filled with ping pong balls...", to which the Denyin'tologists fervently adhere: 

https://www.quora.com/Are-photons-involved-in-all-forms-of-electricity-for-example-when-it-flows-through-wires?utm_medium=organic&utm_source=google_rich_qa&utm_campaign=google_rich_qa

                                            and:

        https://van.physics.illinois.edu/qa/listing.php?id=2348

        It's an established (measured) fact that an electromagnetic wave's propagation and speed, are dependent on the materials, of which the transmission line (cable) are made (ie: Dielectric Constant/permittivity).     The better (lower) the Dielectric Constant the better the flow and the longer it takes for that material to become polarized.     One reason anything that comprises an RLC circuit (ie: capacitors, cables, PC boards), takes time to, "form", or, "break/burn-in".*      

          *Something that makes the Denyin'tologists apoplectic.

   https://resources.pcb.cadence.com/blog/2019-dielectric-constant-of-pcb-substrate-materials-and-signa....

https://unlcms.unl.edu/cas/physics/tsymbal/teaching/EM-914/section5-Guided_Waves.pdf

          Even the most inane (regarding the Sciences) must admit; braiding and twisting wires eliminates/reduces EMI interference.              
          That must lend credence to various cable geometries.

          That better dielectrics enhance the propagation of electromagnetic waves (ie: your music signal), lends the same credence to choosing cables with better materials (ie: Polypropylene, Teflon, air, etc).

           Of course: anything the Church of Denyin'tology's popes can't fathom, they'll summarily dismiss.

         As simple a device as a fuse is: it still carries a sinusoidal signal/voltage, ALWAYS from source to load.

                                                 NOT back and forth!

         Also (as mentioned above): any fuse acts as an RLC circuit, the 'C' of which will be determined by properties of its wave guide's/ conductor's surroundings (ie: glass, air, bee's wax, ceramic, end cap materials, etc).

          Any commonly drawn wire will exhibit a chevron pattern in its crystal lattice, so: why not "directionality" and why OHNO Continuous Cast, single crystal wire sounds better, to so many?

                   Stated above are scientifically tested, measured and proven facts. 

                                  There is no "contest", or "dispute" involved.

         The OP mentions Maxwell, but: obviously they have no understanding of his theory and possible ramifications as regards the above.

          Anyone that feels compelled to harp on not hearing any differences, is obviously too obtuse to understand the term "variables" (as frequently mentioned) and worthy of disregard.

          My only goal in these threads has ever been to encourage those with a mind to experiment with their systems, based on the latest (20th/21st Century's) findings of ACTUAL Physics/science and ignore the Cargo Cult's incessant runway building (objections, convolutions, deflections and obfuscations).

                                                       Happy listening!