Does anyone have experience matching an Icon PS1 MKII with a Soundsmith Zephyr MIMC Star?

I think you mean 470 ohms, not 470,000 ohms.  But you would not want to load your Sussuro at only 100 ohms.

Thank you Antin for the Soundsmith link. I could not find it. That is reasurring.

I have been in contact with Icon. They made the comment that transformers are largely self adjusting.  I also asked them for a schematic of the MC input. They are telling me that there is no schematic since it is merely a 1:10 ratio passive transformer with a required output load of 47KΩ. And that I should follow Soundsmith's advice.

I have contacted Soundsmith, and supplied them with the PS1 MKII Specs. I  am waiting for a reply.

I am also confused about the 100 Ωs. If Icon is using a 100 Ω resistor across the secondary. Then they should have notified me of that, or sent, what amounts to a schematic showing the 100 Ω resistor across the secondary. Which could easily be removed from the circuit.

My calculations were exactly the same as the Soundsmith link.. The source should see a 470 Ω load. Which is perfect. If the Sussuro is seeing 470 Ω. Then that is what I should expect with the Zephyr Star.

I am anxiously waiting for Soundsmith to weigh in on this. I will let you know what they say. But from what is stated in the link. It seems to imply that a 1:10 SUT should do the job of delivering a 470Ω load.

I am also going to supply Icon with that link. And inquire how the 100 Ω load is being calculated.

Since I am unfamiliar with SUTs. This has proven to be an education for me.

Thanks to all for your responses.

You would not achieve a 100R load by putting a 100R resistor across the secondary. God forbid! That would result in the cartridge seeing a 1 ohm load across a 1:10 SUT. But if they inserted a 10K ohm resistor, THAT would result in a net 100 ohm load seen by the cartridge. But it seems they have denied doing that and claim they use a standard 47K ohm resistor at the phono inputs. Which would indeed result in the desired 470 ohm load. (Cartridge load is equal to the value of the resistor on the secondaries divided by the square of the turns ratio; 10-squared = 100. 47,000 divided by 100 = 470.) They cannot have it both ways. So some info is missing OR in fact you have no problem.

Icon appears to be very elusive with giving any kind of definitive answer.  In this review of their PS3 Icon Audio PS1 Mk. II All Valve Phono Stage — Audiophilia Icon expresses their view of step-up transformers stating So, that is why IMHO (and Ortofon + others) a good quality 10x step-up transformer is all you need. (at about 100 ohms).

I am not sure what Soundsmith can add.  They will only know what you know, and be as confused unless they know of a customer who has used an Icon with one of their low output cartridges.  

Here is a review of the Paua and the equipment list is an Icon PS3 which is the reference I found to an Icon and low output Soundsmith.  Just in case, do you have the option to return the Icon, that would be the safest option.

Icon has yet to respond to my question as to how they calculate a 100Ω load. I ask them if they were using a RC across one or both ends. It seems as if they are ignoring the question.

After sending Soundsmith the specs of the PS1 MKII. And describing what my concerns were. Explaining to them, that I felt that I was out of my depth concerning SUTs and asking for any advice that they could give me concerning the issues. After waiting two days for a response. The response that I received was, "Peter says that the Zephyr needs a ≥ 470Ω load." WELL, NO S###!!! I may be unfamiliar with SUTs. But I can read basic specs. Thank you.

Quite frankly, I am disgusted with both companies at this point. I spent $2,000 on a  SS cartridge and that is the best advice that SS can offer?

And as far as Icon is concerned. Give me a break!. You haven't discovered cold fusion, or room temperature super conductors. It is a SUT for god's sake! Why all of the covert BS?

I have another question for this forum that is related to this thread. Can anyone recommend  a company that makes a SUT with a reflected load of 470 ohms or greater, at a reasonable price? I can't seem to find one. I would welcome any suggestions that might steer me in the right direction. I have, once again, ask Soundsmith for suggestions. I will wait to see if Peter has the time to give me a useable response this time. Until then, I must rely on this forum for information.

BTW, I have yet to purchase the Icon PS1 MKII. And I seriously doubt, at this point, that I will. And, as much as I like the Zephyr MIMC. I don't like to be boxed in with no options. I am rethinking my entire approach at this point.

Thanks again for your advice. It is highly appreciated.