Tracking Troubles--Upgrade or Setup?

Ablang -- Any updates? I experience the same thing at times, and I'd be very interested to hear how you resolve the problem.

-Dusty

I experience exactly the same thing, and have (by process of elimination) come tome the conclusion that occasional mistracking definitely occurs. Often, when I simply lift the arm and put it back it helps. I don't want to go any heavier if I can avoid it, and since this is very sporadic, I live with it with no harm to the LPs.

Thanks to Doug's advice this seems more clear. However I have a question for Doug: should I try a little more tracking weight? I have a Rega rb300 arm, admittedly not a high end arm, but gets the job done on my Linn LP12. Thus I prefer less weight/force if I can get away with it. What do you think?

Chashmal,

When "mistracking noises" ("MN's") are heard then actual mistracking, vinyl damage and phono stage clipping are all possible culprits. The next step is to diagnose.

If MN's occur on multiple LP's, both old and new, we can probably eliminate vinyl damage.

Next question, are the MN's in one channel or both?

If the MN's are all (or nearly all) in one channel, you probably have mistracking. Try tweaking antiskating. Increase AS to eliminate R channel MN's, reduce AS to eliminate L channel MN's. If this doesn't affect the MN's, keep reading...

If the MN's occur about equally in both channels or if AS adjustment has no effect, try increasing VTF in .1g increments (until you reach the maximum VTF for your cartridge). If this materially reduces/eliminates the MN's you've found your (a) culprit. Try playing your rig just barely above the VTF needed to prevent MN's. Many cartridges perform very well at that point, which balances the downforce needed to prevent vinyl damage against freedom from unnecessary or excessive cantilever damping.

If none of the above eliminates the MN's, try a different (better) phono stage. Inexpensive phono stages often clip high amplitude signals at certain problematic (to them) frequencies. This can sound so close to mistracking that even expert ears can't tell the difference.

There's also the slow play test to be doubly sure you're not hearing damaged vinyl. "Play" a suspect passage by spinning the platter by hand at VERY SLOWWWWWWWWWW RPM's. The music should sound like a low frequency growl. Any vinyl damage will be much quicker and higher in pitch, very noticeably different from the music. If you hear that the record is to blame and there's no cure. New vinyl can have flaws that this test will reveal, as can old, damaged vinyl.

Oh, you wanted the short answer? Yes, try more VTF! Why not?

:-)

Doug: Yes, it does certainly favor one channel alright, you got it. It occurs on some LPs but not consistently. A given LP might do it now and then, not always. Definitely not LP damage I think.

Here you will have to excuse my ignorance on this matter. I have a Rega RB300 arm which (to my knowledge) has only tracking weight adjustment and no VTF or AS fine adjustment. I am already at the maximum for my cartridge for tracking. I have heard that Rega doesn't honor anti-skating for some spurious ideological reason.

I guess increasing tracking might help. You suggest going over the recommended level a bit?

Chasmal,

A sporadic problem like this points to the need for a holistic approach, first ruling out something further down the chain, like a driver or preamp tube, oxidized RCA connector or bad voice coil. If everything is fine with line-level/CD playback (meaning no noticeable distortions or problems), then move on to the LP chain.

Doug's responses regarding phono chain diagnosis are spot on. My only comment would be that if one uses a cartridge with a somewhat exotic stylus profile, (like the Dorian), alignment becomes extremely crucial. Check, double check and check again. Remember, not all protractors are created equal, and you may have difficulties trying to implement a Baerwald alignment on a Rega, which favors a Stephenson alignment. Also, since you're using an LP12, I would recheck your arm cable dressing through the P-clip. Any hang or drag on the arm cable will cause grief, and can certainly result in the type of distortions you are hearing. The Linn can be funny that way...while you're at it, double check suspension set-up and make sure the platter is level.

-Richard