I use a lined index card folded in half in such a way that the blue lines are horizontal - left to right. This makes a "tent" which I put between the turntable's spindle, and the arm cued down, resting on a record. I line up the arm tube with those horizontal blue lines of the index card tent, and can see quickly if the rear of the arm is not parallel to the front. Personally, I wouldn't be overly anxious regarding VTA...if the arm is parallel, or slightly lower in the back, it is fine. An easy way to adjust the azimuth is to go to your local camera repair shop, and get an old SLR camera mirror...I'm sure he has lots of old ones hanging around and may even just give one to you. I like this mirror, because it is silvered on the face, and is far more accurate than the mirrors most people have which are silvered on the back so that the silver isn't easily scratched off. Anyway, lay the mirror in the turntable with the arm/cartridge resting on the mirror. You should adjust the arm so that looking head on at the cartridge end, the cartridge and the image of the cartridge is exactly square. Joe Grado told me about this setup, and it works well. You can also use an electrical method which others may say is far better, however, it is a pain to do, and offtimes, not nearly as effective. Once you get these two adjustments done, You don't mention what cartridge you are using... if moving coil, I would check to make sure you are happy with the loading. Personally, I don't use side thrust compensation...others do, but I hear no improvement, and indeed less performance using it. Happy listening.
Vinyl beginner frustrations Azimuth and VTA
Hi,
I've had my Pro-ject 6perspex turntable for a few weeks now, and its obvious now that there are several severe problems.
First of all, everything is placed slightly to the left. The soundstage is messed up, and too compact. When I move my head toward the left, vocals move left but stay in focus. When I move toward the right, vocals move right but immediately go out of focus and sound sort of like what you get when you mix up + and - on one speaker.
I guess this means that I need to adjust the azimuth. I've located the screw to do this, but I have no idea how much to move and how much movement is ok before I risk damage to the cartridge. The manual is a bit unclear on whether just twisting the screw is enough to adjust azimuth, or if I actually need to twist the tonearm manually. Could someone with the same turntable enlighten me? I'm also unsure about how the anti-skating weight might influence stereo imaging. There doesn't seem to be very much I can do with the anti-skating weight though, except selecting one of the three grooves.
Furthermore, while bass is tight and generally well defined (if a bit too overpowering on certain kinds of music), highs are virtually nonexistent, this is especially noticable for cymbals, which all but disappear. Midrange sounds more like what I get from cd, but especially vocals are too laid back and too far back in the soundstage
I searched around a bit, and from what I can see, the VTA needs adjustment. Again, I'm not sure exactly how much to move it by. According to this site http://www.walkeraudio.com/fine_tuning_your_turntable.htm I ought to raise the VTA.
However, my (horrible) pro-ject manual says the tube of the tonearm should be parallell to the record when it is lowered, but as far as I can see now it is slanting slightly downward, which would indicate that I should lower the VTA.
Hope I'm not too verbose... just needed to let off some steam :)
PS: I don't have any setup tools yet except the paper aligment tool that came with the table. I did order the one on www.turntablebasics.com though.
I've had my Pro-ject 6perspex turntable for a few weeks now, and its obvious now that there are several severe problems.
First of all, everything is placed slightly to the left. The soundstage is messed up, and too compact. When I move my head toward the left, vocals move left but stay in focus. When I move toward the right, vocals move right but immediately go out of focus and sound sort of like what you get when you mix up + and - on one speaker.
I guess this means that I need to adjust the azimuth. I've located the screw to do this, but I have no idea how much to move and how much movement is ok before I risk damage to the cartridge. The manual is a bit unclear on whether just twisting the screw is enough to adjust azimuth, or if I actually need to twist the tonearm manually. Could someone with the same turntable enlighten me? I'm also unsure about how the anti-skating weight might influence stereo imaging. There doesn't seem to be very much I can do with the anti-skating weight though, except selecting one of the three grooves.
Furthermore, while bass is tight and generally well defined (if a bit too overpowering on certain kinds of music), highs are virtually nonexistent, this is especially noticable for cymbals, which all but disappear. Midrange sounds more like what I get from cd, but especially vocals are too laid back and too far back in the soundstage
I searched around a bit, and from what I can see, the VTA needs adjustment. Again, I'm not sure exactly how much to move it by. According to this site http://www.walkeraudio.com/fine_tuning_your_turntable.htm I ought to raise the VTA.
However, my (horrible) pro-ject manual says the tube of the tonearm should be parallell to the record when it is lowered, but as far as I can see now it is slanting slightly downward, which would indicate that I should lower the VTA.
Hope I'm not too verbose... just needed to let off some steam :)
PS: I don't have any setup tools yet except the paper aligment tool that came with the table. I did order the one on www.turntablebasics.com though.
- ...
- 11 posts total
- 11 posts total