How important is Cartridge Overhang? Need help

Many of us who use the MintLp protractor on a regular basis have found an easy check of the arc position on the table. First, start with the cartridge in the middle of the slots. Then, with the arm lifted on the queue, gently swing the arm across above the arc. You should be able to see if you are in the ballpark or not. If not, move the protractor until it looks like the arm is tracing the arc. Now you should be reasonably close and you can begin adjusting the cart with the stylus down on the protractor.

sorry I haven't been on in a bit . Dan_ed you are exactly right if the Mint had a C point that is where the stylus is landing and if you move the protractor so it lands on the arc near C then at A it is to the left of the arc.I have been talking with Yip at Mint and we have come to the conclusion that the Ortofon HMC 20 cartridge only has a Mounting Hole to Stylus Tip of 8.5mm instead of the standard 9.5mm. That looks to be the amount of adjustment missing. Since it looks like I may have to replace the cartridge does anyone have any suggestions on a sub $500.00 cart. with a known longer MHST measurement.Ortofon would be preferred just because of the trade in, but it is not a must

Hi, Wilson667: A difference of only 1.0mm should not prohibit you from adjusting the position of the cartridge in the 9cc tone arm headshell to align to the Lofgren A/Baerwald geometry. The headshell slots have enough play forward and backward from the middle position, which accomodates most cartridges with typical mounting hole to stylus distances of +/- 9.5mm, to easily accomodate your HMC 20.

Something doesn't sound right. Before spending money on another cartridge, try using the Conrad Hoffman protractor, which works very well for the Pro-Ject tone arms. Download from the link, unzip, print, and follow directions in the README file.

http://www.conradhoffman.com/TemplateGen.zip

Tom

Wilson667,

When you moved the protractor back to get the stylus to land to the left, could you then move the cart back in the slots toward the line? If not, I suspect that the arm is not mounted exactly at the P2S distance. However, the distance between the stylus and the line will give you an idea of how much the arm pivot is off. I remember the Pro-ject arm I had on an MMF-7 a while back, but don't remember how much play there is in the three set screws that hold VTA. Maybe it is possible to play with this and get the P2S correct? Can you measure carefully what the P2S distance is now?

Granted, a short hole-to-tip makes life a bit difficult but if things are set correctly and your arm has slots for mounting the cartridge it should work. There is no standard for the hole-to-tip distance. That is why most arms have those headshell slots.

Dan_ed; I would also consider that the Mink protractor may not be constructed correctly. If the wrong parameters were given or used to set the markings on the protractor that could also account for the problem trying to use it with the Pro-Ject 9cc tone arm. There should be more than enough play in the headshell slots to accomodate a 1.0mm difference in cartridge mounting hole to stylus tip distance. Unless Pro-Ject has recently redesigned the 9 series tone arms, a typical cartridge with 9.5mm mounting holes to stylus tip distance puts the cartridge right in the middle of the slots with almost 3mm of travel fore and aft.

That's why I asked what dimensions were used to create the Mink protractor: Are they the correct dimensions? Using parameters of 212mm spindle-to-pivot distance and a 230mm effective length the cartridge should easily align to a Lofgren A/Baerwald geometry with the Pro-Ject 'arm. And also why I suggested using another protractor with the correct parameters to compare with the Mink protractor. Conrad Hoffman's TemplateGen is a quick way to check. That would indicate if it's the Pro-Ject turntable or the Mink protractor that was possibly mismanufactured.

Until more information is provided all bets are off as to what is causing the problem.

Tom