Dear T_bone: The Exel spreadsheet is very good idea.
About an increment on the EL the " land " you have to move is limited by the headshell slots and is posible that 3-4 mm makes no diffrence that you can hear.
If these kind of changes on the geometry set up beeen the only factor on the cartridge quality performance then is for sure that you can detect a minimum/tiny EL changes but there are other factors and IMHO other very important ones that a some levels preclude we can detect tiny EL changes. everything is important on cartridge set up but IMHO VTA/SRA and Azymuth makes the higher differences ( other than a matched tonearm. ).
Other that to use any of the protractors out there ( DT included. ) IMHO ( if we want to stay with mind on calm, even if we can't hear some geometry set up changes. ) a good alternative is to measure the most inner groove in our LP collection and take a choice with foundation on what are that LP collection if the 80%-90% of the Lps measures around 60mm then the IEC standard is the best choice in either Löfgreen A/Baerwald and Löfgren B and from these two if we want lower distortion at innergrooves then the choice is Löfgren A/Baerwald that additional gives you the same tracking error between null points and outer null points: this is very good compromise.
In the other side if the 80%-90% of the LPs in your collection are around 50mm or lower then you can choice between Stevenson or Löfgren A/Baerwald with non-IEC standard for the most inner grove data instead you change that input data for 50mm. I prefer this Löfgren A/baerwald that gives you sligthly ( tiny ) higher distortion that Stevenson at the very inner grooves but with lot lower distortion levels on all the remaining recorded LP area: this for me is very good compromise too.
That's why Löfgren A/Baerwald is the most used geometry set up.
IN the other side IMHO Stevenson was and is used by Japanese manufacturers because ( with all respect ) they did not a in deep analisis on the overall subject and its different alternatives, I already posted that I know this because I asked them about with no certain answers that could tell me they have in deep knowledge.
T_bone if it is true that this geometry set up cartridge/tonearm is something/subject really simple it could be very complex if we don't understand its foundation and alternatives.
I know many people don't understand yet and I don't blame any one for that. As I posted reviewers, audio distributors, tonearm designers and audio " gurus " does not understand in deep either, this is where a thread like this has a critical an important role for we improve our each one knowledge level on the whole subject.
The real value of discussions like the ones we have here and especially between DT and I IMHO always help ( one way or the other ) to lear, I can tell you for sure that I learned here too.
My attitude to " win " a discussion that I had on the past I left on the past even that sometimes you could think I want to beat DT or other person but it is not in that way, if I " insist " is because either I don't find true arguments against in the other person or because I'm challenged my own arguments/opinion till its fall/down or confirm it.
One of the best way to learn is through discussion with other people if what you move is to learn and not only who is right where you can't learn.
Regards and enjoy the music,
Raul.
About an increment on the EL the " land " you have to move is limited by the headshell slots and is posible that 3-4 mm makes no diffrence that you can hear.
If these kind of changes on the geometry set up beeen the only factor on the cartridge quality performance then is for sure that you can detect a minimum/tiny EL changes but there are other factors and IMHO other very important ones that a some levels preclude we can detect tiny EL changes. everything is important on cartridge set up but IMHO VTA/SRA and Azymuth makes the higher differences ( other than a matched tonearm. ).
Other that to use any of the protractors out there ( DT included. ) IMHO ( if we want to stay with mind on calm, even if we can't hear some geometry set up changes. ) a good alternative is to measure the most inner groove in our LP collection and take a choice with foundation on what are that LP collection if the 80%-90% of the Lps measures around 60mm then the IEC standard is the best choice in either Löfgreen A/Baerwald and Löfgren B and from these two if we want lower distortion at innergrooves then the choice is Löfgren A/Baerwald that additional gives you the same tracking error between null points and outer null points: this is very good compromise.
In the other side if the 80%-90% of the LPs in your collection are around 50mm or lower then you can choice between Stevenson or Löfgren A/Baerwald with non-IEC standard for the most inner grove data instead you change that input data for 50mm. I prefer this Löfgren A/baerwald that gives you sligthly ( tiny ) higher distortion that Stevenson at the very inner grooves but with lot lower distortion levels on all the remaining recorded LP area: this for me is very good compromise too.
That's why Löfgren A/Baerwald is the most used geometry set up.
IN the other side IMHO Stevenson was and is used by Japanese manufacturers because ( with all respect ) they did not a in deep analisis on the overall subject and its different alternatives, I already posted that I know this because I asked them about with no certain answers that could tell me they have in deep knowledge.
T_bone if it is true that this geometry set up cartridge/tonearm is something/subject really simple it could be very complex if we don't understand its foundation and alternatives.
I know many people don't understand yet and I don't blame any one for that. As I posted reviewers, audio distributors, tonearm designers and audio " gurus " does not understand in deep either, this is where a thread like this has a critical an important role for we improve our each one knowledge level on the whole subject.
The real value of discussions like the ones we have here and especially between DT and I IMHO always help ( one way or the other ) to lear, I can tell you for sure that I learned here too.
My attitude to " win " a discussion that I had on the past I left on the past even that sometimes you could think I want to beat DT or other person but it is not in that way, if I " insist " is because either I don't find true arguments against in the other person or because I'm challenged my own arguments/opinion till its fall/down or confirm it.
One of the best way to learn is through discussion with other people if what you move is to learn and not only who is right where you can't learn.
Regards and enjoy the music,
Raul.