Sakura Systems OTA Cable Kit

I agree with the post - several posts back - about not twisting the cable. The sonic result is awful.

However, one configuration that sounded very good to me was;
- get a length of plastic rod or tube with good dialectric qualities and good flexibility - usually a foam rod is best
- wrap one conductor around the rod, from end-to-end, circling the rod once every six inches or so.
- do the same with a second conductor but wrap it counter to the first one, so that it is therefore crossing the first one twice every six inches.

I suppose in theory this configuration has lowish capacitance, and lower inductance than letting the cable fall chaotically on the floor (the approved method). Whatever, the result sounds cleaner to me. Certainly, I prefer the physical result too.

Don't ask me where I got the central foam rod - I took it out of the center of some Straightwire speaker cable I didn't mind butchering.

So far I have used three Storatos power cables in my system. Two 20 ft runs direct from 230 Volt AC wall socket to each VAIC SET monobloc and one 6 ft run between a dedicated-digital power strip to a z-systems digital preamp/equalizer.
I will certainly add more Storatos PCs now after hearing this arrangement, since the use of my existing PC cables (all of them NBS Statements) seems more problematic (mechanically, electronically, sonically) than not having them. I am certain that the Storatos cables improved the ability of the z-systems preamp to handle complex frequency- and dynamic-related information in the digital domain, and that it enhanced the transient characteristics, detail and reproduction of frequency extremes (crisper treble, tighter bass) of the VAIC monoblocks. This latter result was surprising since the VAIC monoblocks have some special "challenges" with their power supply and require exteme care when it comes to mains voltage--I will spare you the details. In short, let me just say that I was shocked that Storatos could function as such an excellent power cable for these power-hungry units, fast enough to cover their sudden demands in energy.
Some tips for making up Storatos PCs.
There are lots of metal parts in every stock IEC and PC plug I have examined: mainly screws for the wires, wire guides, and lead systems for + - and ground. These can be a problem if you want to minimize intermediary connections between Storatos and your house mains cables or the hook-up wires to your components transformers.
If you plan on using an AC plug, try to find one with solid copper prongs (German high-end manufacturer "Phonosophie" provides copper tip plugs for the Schucko system). If your house has Schucko outlets (i.e. you live in Europe), you can also use two 47 Labs speaker banana plugs as AC plug prongs and make a direct contact between Storatos and your house mains this way. (BE VERY CAREFUL TO AVOID SHOCK!) This solution is not possible for the American plug system. But you can still always make a direct "pressure" contact between Storatos and your house mains. (This goes without saying, but, TURN OFF YOUR HOUSE MAINS BEFORE YOU DO THIS!)
As for the other side of the Storatos power cable, I have used both light-weight PVC and rubber IEC female plugs (I actually prefer the cheaper PVC variety). One important tip: Do not simply crush the bare Storatos wire under the screw clamp! Instead wrap the bare Storatos around the IEC "U" brackets/guide (leaving enough Storatos insulator stripped away to allow the male IEC prongs to fit fully into the female "U" receptables) so that the male IEC will make direct contact with the Storatos wire. Affix Storatos in the IEC by screwing down on the beginning of the insulated portion, being careful not to break or strain the wire inside.
You may want to leave the halves of the IEC relatively loose until you have the female IEC (with the Storatos bent around the very tip in a "V" formation) fitted over the male IEC prongs of your component. Then you can finally affix the two IEC halves together by fully tightening the screw that holds the two halves together after the IEC is inserted into the component.
As far as defeating the third (center, ground) prong on the ac line-cord by removing it, I will leave a few warnings. This third prong provides a ground connection, which not only helps prevent pickup of RF interference but prevents possible damage to components. This ground return is legally required by Underwriter's Laboratories, a branch of the National Board of Fire Underwriters (in the USA) and by EU regulations (in Europe). Not only can some equipment get damaged by removing the ground, but a fire hazard can be introduced. If your house burns down and the investigation of the remains reveals that you were operating equipment without grounds connection, your insurance company is not liable to pay any of your claims. They will simply look at it as your negligence to provide protection from excessive current risks.
Note that it is no advantage to shield Storatos ac power cables. Note also that lengthening the ac cable to 20 feet, as I did, did not impose excessive power loss. If high-frequency response was lowered by such a long power cable, then that is a matter of no technical concern, and even an advantage: hifi equipment is operated in Germany at a frequency of 60-Hz ac, well below the high-frequency loss (starting from 2,000 Hz) imposed by long lengths of connecting cable.
One final "tip": I think dekay already said this, but if you solder Storatos wire, a small soldering iron is advisable. You will want to use as little solder for your connection as possible. Modify your soldering iron to limit the amount of heat and solder that is applied to the circuit board terminal point. Use a short length of bare Storatos wire wrapped around the tip of the soldering iron, and cut to a tip of approximately 1/4 inch. After prolonged use, the wire will become corroded and pitted, and must then be replaced.

OTA Power Cords. I'll try your method with my next 2 Power Cords. I've already done 5 Power Cords and the improvements brought about by the OTA power cords are pretty amazing. Fantastic value for money compared to what good PCs are going for these days.

»In short, let me just say that I was shocked that Storatos could function as such an excellent power cable for these power-hungry units, fast enough to cover their sudden demands in energy. »

Slawney, you are continuosly surprising me with your pioneer spirit!

Franky, I would say feeding you VAIC with mains from tiny 47Labs cable is an overkill. I wouldn't dare even try that! Well, I couldn't sleep the first night I had my low power consumer setup hooked on it but I think I told you about that.

Why did you need 20ft power cables? You had them hooked to the mains in the other room?

»There are lots of metal parts in every stock IEC and PC plug I have examined: mainly screws for the wires, wire guides, and lead systems for + - and ground. These can be a problem if you want to minimize intermediary connections between Storatos and your house mains cables or the hook-up wires to your components transformers.«

No problem at all! Just throw away ALL the metal not strictly related to contact making. You can glue back IEC and PC plugs instead of screwing them back with metal screw. From an ordinary PC plug and three IEC connectors I usually end up with fistfull of pieces I put into dump.

»If you plan on using an AC plug, try to find one with solid copper prongs (German high-end manufacturer "Phonosophie" provides copper tip plugs for the Schucko system).«

Did I tell you that one? Actually, I didn't know about that one but when talking on the subject with Jonathan Carr, he raised my attention to this product.

»If your house has Schucko outlets (i.e. you live in Europe), you can also use two 47 Labs speaker banana plugs as AC plug prongs and make a direct contact between Storatos and your house mains this way. (BE VERY CAREFUL TO AVOID SHOCK!) »

In all seriousness, that is something I would not like people start doing… Are the extra bananas you ordered last time for that? If so, good I didn't have them in stock… Forget about getting them, unless using them for speakers, hehe. I intend to see you in May and not to bring flowers to your tombstone.

»As for the other side of the Storatos power cable, I have used both light-weight PVC and rubber IEC female plugs (I actually prefer the cheaper PVC variety).«

I agree that PVC should be better. What counts here is, of course the conducting material. Copper, then brass, then rhodium would come on my list. Nothing else. No plating.

»One important tip: Do not simply crush the bare Storatos wire under the screw clamp!«

A very easy thing to do…

» Instead wrap the bare Storatos around the IEC "U" brackets/guide (leaving enough Storatos insulator stripped away to allow the male IEC prongs to fit fully into the female "U" receptables) so that the male IEC will make direct contact with the Storatos wire. Affix Storatos in the IEC by screwing down on the beginning of the insulated portion, being careful not to break or strain the wire inside.«

This one is tricky and I sense problems with this arrangement (as in most cases, a good contact will remain to be desired, if not done right).

»As far as defeating the third (center, ground) prong…«

I checked mine and haven't seen any center prongs left, hehe.

»… on the ac line-cord by removing it, I will leave a few warnings. This third prong provides a ground connection, which not only helps prevent pickup of RF interference but prevents possible damage to components. This ground return is legally required by Underwriter's Laboratories, a branch of the National Board of Fire Underwriters (in the USA) and by EU regulations (in Europe). Not only can some equipment get damaged by removing the ground, but a fire hazard can be introduced. If your house burns down and the investigation of the remains reveals that you were operating equipment without grounds connection, your insurance company is not liable to pay any of your claims.«

Which, I think, probably is the case if used power cables of lesser diameter than required by the power rating of the appliance… It's a slippery territory we are talking about here and I can not recommend to anyone to make power cables from Storatos.

But, if you do….

Why bother with multiple cables? That leaves you with problems.

Why not use one PC plug and run multiple IEC's out of it?

So, you need three power cords, for example… Take 6 runs (9 runs if intending to keep the grounding), mark three of them (and onother three for grounds, yet in another color) at cable ends on both sides. On one side, wrap threes of the same color together and fit them into PC plug.

Other sides of cable, one of each color go to IEC plug, making sure to fit each of them to IEC on the same place (if wire colored red is in one IEC connector on the left side, it should be on the left side in the other two IEC plugs as well. If using ground, wires colored as ground MUST go to IEC grounds, of course. This is valid for Shucko mains plugs system where PC plug can be plugged two ways to match required polarity. For UK, one must make sure that Live comes to the right side of IEC plug, looking at IEC conenctor from the front side, flat side down…

This way, you can be sure that each of your components has exactly the same polarity orientation, no need for extension cord (so you want to make it long enough to reach the wall plug), less metal, etc…

»Note that it is no advantage to shield Storatos ac power cables.«

Very much agreed.

Best regards,
Sead

Would like to try it myself. Anybody wants to go for it together? I'll just need 6-7' for two interconnects and maybe 16+' for speaker cable. So more interested parties cheaper for all. Let me know!