Why Rhodium?

ANY time 2 different metals come into contact you form what is called a junction. It is called a thermocouple and produces a (minute amount) electrical current. While I wouldn't expect it to be a factor in power or power supply, it could be a large fraction of low voltage circuits, like phono.
This effect, (thermoelectric effect) should drive those nuts who can hear which way a fuse is installed in a power supply.
Rhodium is used in such couples, for many of the properties listed above.

Don't believe me? Get out a steel coat hanger and a piece of #12 copper wire.
Twist the ends firmly together. Use a vice and pliers if you have to. Connect the free ends to a DVM (what? You don't have a DVM? Shame!) and stick a match under the junction. You should get a couple MV, at least.

On top of that, you guys are kidding yourselves if you believe that the material used for the connector plating will have an enough effect on a signal to be audible, if even measurable.

yes this is why, for example if you compare the Oyaide 037, 046, 079 plugs which have the same exact construction except the plating, being silver/rhodium, gold/palladium, and gold/gold respectively, and you put them on the exact same built cord they sound exactly the same! The different color ends are only for WAF and for the fashion conscious audiophile so as they don't clash with the rest of their system.

IMO, the issue is more complex than just conductivity of the plating as a cause for differences in sound with various platings materials.

The FI-28M(R) appears to be the “little brother” to the FI-50, both being made of rhodium over pure copper. I suspect the sonics are similar. I've found the FI-28M(R) to have excellent dynamics, smoothness, transparency, detail, decay, and soundstaging, while remaining tonally balanced, with no glare.

My rhodium plated Kaplan cable sounds slightly more lively and detailed, as compared to the pure copper version. The cordage is the same.

I know that some rhodium connectors use a silver underplating. Perhaps that is the source of the glare?

I don't believe that rhodium will necessarily cause any loss of detail or transparency, as compared to a higher conductivity material. My experience is just the opposite.

I’ve also tried the FI-25Gs, but they sounded somewhat bright, with some glare.

Another example of interesting material is palladium. I use a Pure Note Alluvion digital cable, and the palladium in it sure takes the glary edge off of the silver. However, this is an alloy, and not a plating.

Nickel is another story. It always seems to cause glare for me.

"Perhaps the most interesting fact revealed by this chart is how low most copper alloy materials rank in relative conductivity. One might easily assume that alloys such as the brasses and bronzes, because they are mainly copper, are nearly as conductive as copper. This is not the case. The small percentages of tin, aluminum, nickel, zinc and phosphorus that make up these alloys degrade the electrical performance of the resulting alloy to a far greater percentage than their compositional percentage in the alloy.

One should not conclude from this, however, that brass should never be used in electrical applications. There are instances where the superior tensile and machining characteristics of brass make it a better choice than copper as long as the sectional areas are increased proportionately to achieve the conductivity that a copper part would have in the application. Size for size, however, copper is exceeded only by silver among the materials commonly used for electrical applications."

www.kp44.org/ftp/ElectricalConductivityOfMaterials.php

Couldn't copy the chart but it's at the above website.

Size matters :-)

Rhodium has the best resistance to corrosion over any current material being used for termination. I own several audio components that have been in a cottage next to Lake Erie (high humidity) for 20 years. The heat is off 6 months out of the year with almost constant 80% - 100% humidity. Rhodium is the only material that has not shown signs of surface corrosion under this condition. Silver, copper and gold all eventually broke down with surface build up. Steel connections were rendered useless and couldn't even be cleaned.