2. tech-talk
  3. 1421239386

my ethernet cable?

Hi all-

Another beginner question. So I am planning to set up a device (either an Auralic Aries or a Sonos with Empirical Audio's Synchro-Mesh and Dynamo power supply) to stream Tidal. When I was having a TV installed last year, I had the guy pull an ethernet cable to my stereo cabinet with this purpose in mind. I thought I was being smart to ask for him to get and install cat 6 instead of 5e, which was what he usually uses.

Later I read that cat6 can be a lot trickier to install correctly, and sometimes its safer just to go with 5e. (and I note the adapter plate on the wall actually says 5e.) And then I read this article from Blue Jeans cable about how most of the cat6 cable on the market is crap.

http://www.bluejeanscable.com/articles/is-your-cat6-a-dog.htm

So all of this has me wondering if I should buy some cat6 from blue jeans (or even 5e given installation quirks with cat6?) and have this redone? Or is there a way to test the quality of the cable I have and know whether or not it is up to the task?

It seems a bit excessive to replace the cable, but on the other hand, that will cost a fraction of what an Aries streamer does, or a year's subscription to Tidal, so I am wondering if I shouldn't make sure my fundamentals are all solid before proceeding.

Any advice?

Thanks!

Margot
mcanaday
mcanaday OP
169 posts
 

Jim and Al,

You guys are the best. Thanks so much. So it sounds like my first step is just to go ahead and as long as I don't hear drop outs, don't worry about it. If I do hear drop outs, then maybe I want to get some shielded cat6 from blue jeans cable, if possible. If I end up there, Jim, will most electricians know about how to terminate correctly etc, or should I try to track down a certified cable installer? with enormous thanks to you both,

Margot
mcanaday OP
169 posts
 
Oh, one other follow up:

If I do end up having drop outs and needing to replace the cable, I assume I only have to replace the line that goes to my stereo? (ie: I can leave the line that runs to the computer and the line that runs to the TV as is.) Or will this affect the performance of the new cable I have installed as well?
Thanks! M.
almarg's avatar
almarg
9,670 posts
 
Thanks for the nice words, Margot. Regarding your last question, correct me if I'm wrong but I'm envisioning that the cable in question goes between the stereo and a router or network switch or something comparable. If so, the other lines will not affect the performance of the new cable. Also, if I understand correctly those other lines can be presumed to be functioning in a reliable manner, or you would have already noticed problems with them. That being relevant, for example, if you were to play music from the computer to the stereo via the ethernet connections.

Best regards,
-- Al
jea48
4,659 posts
 
Margot,

IF, you have problems and the problem turns out to be the Ethernet data cable, you do not need to hire an electrician. You need to find a good low voltage cable company in your area that has trained certified data cable installers. You also need to make sure the company has/uses the proper test equipment to certify the cable after the data cable has been installed and terminated with RJ45 jacks and or RJ45 plug ends. The company should be able to furnish you with a copy of the test certification.

LOL, I noticed in my earlier response to your posted message I typed RG45 jacks instead of RJ45 jacks. It should read RJ45, So much for proofreading, my bad.
Jim
bgoeller
73 posts
 
If you are intent on listening to them both, why don't you get a run of 5e and just try it out without having it installed in the wall? If you like it better, then have it strung properly.

I have used neither for audio purposes, but did just have 15 miles of cat6 installed in our new corporate HQ with some runs well over 300 feet, and not a single cable has had to be replaced or reterminated. The majority of the drops are used for business class workstations, but we do have some server class machines with persistent DB connections where packet loss has to be minimized.

If I was being asked this question specifically for a data network build I would recommend cat6. For audio, your mileage may vary.
More to discover