Here is my 2 cents.
Im gearing up to start on my DYI HT project, gonna built all the speakers/amplifiers/cables
Ive had lots of experience with Mid-priced HT gear, with no single component breaking the 1,000MSRP mark. Been through many setups in many rooms, and over the years the experience i have gained determined my goals on construction.
1) Pre-Processor, no Reciever. The benefits of outboard amplification is obvious to all who have heard.
2) 150WPC, all 7 amplifiers will be monoblocks and identical in every fasion.
3) All speakers will be identical. No "center" channel, no Bipole surrounds, all 7 speakers will be exactly the same. Every time i did the sound level adjustments, even with "Voice matched" gear the FL/FR did not sound exactly the same as the center, nor did the LS/LR BL/BR. Normally the f/l and f/r had more depth which the center and surrounds lacked.
4) Being identical speakers, the center channel cannot be a "full sized" speaker therefore neither will any of the other speakers, they will all be Monitors.
5) Full Range, even though they will be monitor size, they will be larger monitors, and im going to to my best to make sure they can all reach down to 45Hz -3db, i want the center and surrounds to be as close to "full range" as possible. None of this "down to 100hz" crap. All 2 way speakers
6) Dual Subwoofers designed with the goal in mind of reaching down to 20hz with no more than a -6db loss.
250rms Amps to power them.
7) Projector is a must in this setup. I want a good 100" screen minimum.
8) No integrated 2 channel. This will be in a room dedicated for Home Theater, not for music. Therefore all considerations for 2 channel will be ignored, im going for a seperate 2 channel system in another room. The focus of this will be HT and HT only.
9) Room treatments.
If i were to just go out and buy this same setup rather than build it myself, the requirements would not change, except i might go for a 7channel amplifier rather than 7 monoblocks.
Im gearing up to start on my DYI HT project, gonna built all the speakers/amplifiers/cables
Ive had lots of experience with Mid-priced HT gear, with no single component breaking the 1,000MSRP mark. Been through many setups in many rooms, and over the years the experience i have gained determined my goals on construction.
1) Pre-Processor, no Reciever. The benefits of outboard amplification is obvious to all who have heard.
2) 150WPC, all 7 amplifiers will be monoblocks and identical in every fasion.
3) All speakers will be identical. No "center" channel, no Bipole surrounds, all 7 speakers will be exactly the same. Every time i did the sound level adjustments, even with "Voice matched" gear the FL/FR did not sound exactly the same as the center, nor did the LS/LR BL/BR. Normally the f/l and f/r had more depth which the center and surrounds lacked.
4) Being identical speakers, the center channel cannot be a "full sized" speaker therefore neither will any of the other speakers, they will all be Monitors.
5) Full Range, even though they will be monitor size, they will be larger monitors, and im going to to my best to make sure they can all reach down to 45Hz -3db, i want the center and surrounds to be as close to "full range" as possible. None of this "down to 100hz" crap. All 2 way speakers
6) Dual Subwoofers designed with the goal in mind of reaching down to 20hz with no more than a -6db loss.
250rms Amps to power them.
7) Projector is a must in this setup. I want a good 100" screen minimum.
8) No integrated 2 channel. This will be in a room dedicated for Home Theater, not for music. Therefore all considerations for 2 channel will be ignored, im going for a seperate 2 channel system in another room. The focus of this will be HT and HT only.
9) Room treatments.
If i were to just go out and buy this same setup rather than build it myself, the requirements would not change, except i might go for a 7channel amplifier rather than 7 monoblocks.