2. cables
  3. 1019414801

Try this simple DIY interconnect cable.

Okay, I'd like to weigh in here on the cable issue. First, let me make it perfectly clear that I am not the world's greatest cable expert, I have never heard Valhalla's, Jena Labs, or alot of the others. I am a regular working Joe who thinks that cables do make a difference but can't afford $5k-$10k to buy them. I tried out an idea that I read on the web, and changed it a little, and I thought it sounded great on my system. So here it is, a nice sounding IC for dirt cheap. Go to the Rat Shack and get their magnet wire pack($2.99). I used the 30ga for mine, but you get 26ga and 22ga spools in the pack so you can use thicker if you like. Go to Lowe's and get the 1/4" polyethylene tubing in the icemaker parts section(25ft for $2.50) Get a couple rolls of teflon tape($1.00). Cut off 1 meter(or what you need for each channel) of tubing. Wrap it with the teflon tape in a spiral. Take your magnet wire and wrap a spiral around the entire length with about 2" spacing(18 turns per meter).Leave a couple inches extending on both ends to solder to the connectors.Then wrap the whole length again with teflon tape as a jacket.Make sure the wire gets covered - no gaps. Then thread another piece of the same guage wire down the tube and out the other end. Leave "tails" on both ends, like before. Solder your favorite RCA plug to each end using the center conductor for signal, and spiral wrapped wire for ground. The ones I used had a spring type strain relief that fit right over the teflon covered tube perfectly and looks professional. Then make one for the other channel. Takes about 2 hours total. They're flexible, sturdy, don't fall apart, look good, and sound real good on my system. Now, you can make your comments about inductance, capacitance, whatever. What we've got here is a good sounding cable with a mild level of RF rejection, teflon dielectric, reasonable spacing between conductors, for a dirt cheap price. I would like an enterprising individual with some good quality cables to make a pair of these and see how they stack up against a good commercial product. Dr. Gizmo, where I got the basic idea from, said that they were better than all his exotic stuff. I don't know about that, but they do sound good on my system. Maybe we could all get lucky and be able to save alot of cash.Probably won't beat Valhalla, but for many of us it might be good enough. Share your thoughts, please. And I would love to hear a report from someone who made them and compared.
twl
sean
6,231 posts
 
The late Harvey Rosenberg of Listener and NY Audio Labs popularized a similar design many years ago. You could just as easily twist the two wires around each other, creating a twisted pair. Since they are enameled, you don't have to worry about them shorting out. If you are worried about something like that, try using the individual conductors from some CAT 5 cable. The better stuff is Teflon insulated and it is solid core 24 gauge. It comes pre-made as multiple twisted pairs, so you would only have to terminate the wire into the RCA's.

David Magnan was the first one to try using MEGA thin wire for interconnects. He did this after studying time delay distortions and skin effect. He has since gone from using small gauge wires ( 36 gauge ) to conductive paint. Since the conductive paint literally has no depth, it is all "skin" for increased surface area.

As to the bottom line, i too agree that you can make some pretty phenomenal interconnects for next to nothing. Sean
>
twl OP
3,251 posts
 
Sean, that is where I got the basic idea - Harvey "Dr. Gizmo" Rosenberg.
dklap
51 posts
 
what connectors do you recommend? also, instead of putting the signal wire down the middle, what about wrapping the signal wire around the tube as well, spaced out so they don't touch? and is there any advantage to using teflon tape coated polyethylene tubing rather than plain old teflon tubing? trying to figure what route to go. must upgrade from monstercable and don't want to go broke.
twl OP
3,251 posts
 
Good question. I did not try wrapping both conductors, evenly spaced, around the tube. I did read about that method though. The reason I put the signal conductor down the middle of the tube is because it is a much oversize tube and I wanted the "air dielectric" around the signal wire. I didn't find any teflon tubing in my hardware store, so I used polyethylene. If you can find teflon, then I think that would be better, or at least just as good. I think the "air dielectric" idea actually works, and I used the same oversize tubing on my 22ga solid core speaker wires with a separate tube for each conductor. I spaced them apart with 2" spacers and got very good results from them too. You can experiment with this stuff pretty cheaply, so you can try different methods. I am not claiming this is the greatest, but it does sound real good for very little money.
cdc
1,773 posts
 
Could also do 2) grounds and 1) signal as Kimber does on the PBJ's.
More to discover