2. amps-preamps
  3. 1394129996

Tube Amp for Martin Logan Speakers

Hi, I love tube sound through my Martin Logan Aerius-i fronts and Cinema-i center. I currently have a Butler 5150 which is a hybrid, but it busted on me and would cost $700 to fix. I've had china stereo tube amps that were pretty good and gave true tube sound, but not enough drive for higher volumes. I live in condo, so not like I can blast music anyways but still. I got the Butler because I wanted 5 channel tube sound for home theatre (The piercing sound from my Denon 3801 receiver was not pleasant to my ears). It appears there are only three multi-channel tube amps around, from Mcintosh, Butler 5150, and Dared DV-6C. The latter two are hybrids, and the last one was one of the worst tube amps i've ever heard. I have no clue why 6Moons gave the Dared a 2010 award, but maybe it's because it produces only 65W.

So since multichannel tube amps are hard to come by, and they tend to be hybrid, I was thinking maybe it would be best to get three true tube monoblocks to power my fronts. Thing is I wonder if they will be underpowered for my speakers, and not sure which ones are decent for the price. Maybe China made ones would suffice, and they still go for pretty expensive price. I'm wondering if anybody knows of a decent powerful tube monoblock that is affordable, because I can't pay $3000 per block. or maybe best to just repair my Butler. Thing is, I'm not confident that it is reliable. The tubes are soldered in which is weird, and i've taken it to a couple repair guys who both said that the design is not good, because it's very tight inside and more susceptible to being fried from DC voltage areas. it's too sensitive.

Any suggestions for tube monoblocks, even if china made ones? the holy grail for me would be Mcintosh tube amp, but they are hard to come by. Thanks.

smurfmand70
bifwynne
2,206 posts
 
Well stated Mapman! :)

I think the EPDR link I provided supports Ralph's comments that low impedance speakers may have an even lower EPDR rating than what is nominally reported or measured. Even more important is that speakers presenting low EPDR factors significantly contract an amp's so-called SOA.

I am not saying that 4 ohm speakers are not good performers. Just that a nominal 4 ohm load in the bass region may really squeeze the amp and possibly result in a referral to the SPCA. At a minimum, a less than optimal amp/speaker match may, as the article explains, result in distortion. So, I happen to think Ralph's comments make sense for the reasons set forth in the attached article.

Bruce

P.S. The SPCA is the Society for the Prevention of Cruelty to Amplifers.
atmasphere's avatar
atmasphere
11,807 posts
 
BTW, as I read it; George didn't call you stupid, he called one of your suggestions stupid, and that was after you called him a "troll", which was after he posted a link where he recommend your product. This line of posting is somewhat out of character for you.

Hi Unsound, yes it is, and one should consider that I do refrain from that sort of thing as much as I can. Recommending the ZERO is something I have done a lot, and not just for our amps and I will continue to do so despite George's remonstrations. This is for no other reason than the ZERO really does work.

One other thing- to clarify, I am not stating that 4 ohm speakers are bad speakers. I am stating that any amplifier driving them will sound harsher and less detailed as opposed to the same amplifier driving the same speaker that was 8 ohms, were all other matters to be equal. Put another way, a simple method of making a speaker seem more transparent and easier to listen to is to make it be higher impedance.

This might be all about how important it is to an audiophile to have increased transparency/detail, coupled with a smoother presentation. I like those things myself.

Something I have not mentioned yet is the effect of the speaker cable on 4 ohm speakers- but it should be obvious that they are far more critical for a 4 ohm speaker than the cables are for 8 or 16 ohms. Damping factor of amplifiers is normally stated with respect to an 8 ohm load; that number is initially cut in half with a 4 ohm speaker. Add to that the seemingly low DC resistance of the speaker cable and the damping factor of the amplifier is reduced considerably more that one might intuit. RCA published a nomograph that showed this relationship several decades ago.
mapman's avatar
mapman
22,213 posts
 
YEs, but realize that tube amps in general will distort even more than SS amps into 4 ohms, so if 4 ohms is part of teh puzzle, the answer is clear.

Any good amp, SS or otherwise can drive an easy load easier.

SO you have to look at all the pieces of each puzzle together in the right way , not take one piece from one puzzle and try to insert it into the the other and then blame it for not working.

Likewise, there is always good, better and best in any case/scenario. Its important to understand impedance and phase related issues in order to assemble the right pieces. Then you can assess system/puzzle A versus B however one likes, but better to look at the overall results than the relative deficiencies or strengths of any one element of design.
georgehifi's avatar
georgehifi
10,312 posts
 
03-27-14: Atmasphere: do so despite George's remonstrations

Are you kidding, far from pleading with you Ralph.

I agree that an Autoformer is a great (pseudo) bandaid fix for whatever amp that cannot drive a speaker that is not a good match, because of it's inability to deliver current/wattage or is working out of it's SOA (safe operating area) A FAR BETTER FIX IS TO CHANGE THE AMP/S OR SPEAKERS!

You state that even a good solid state amp will measure less distortion on it's output from using a Zero Autoformer into a 4ohm load compared to 8ohm.

Yes I agree that with the Autoformer even a good solid state amp will measure slightly less distortion at it's output terminals at 4ohms (this is not to say it's out of it's SOA)
But it's what happens after the Autoformer (things like phase shifts, damping factor etc) that is far more detrimental to the sound than the slight increase in distortion before it without the Autoformer.

EG: What one would basically do to a good amp say like a Pass Labs, Krell, Gryphone or similar amp by sticking an Autoformer on it, is to turn it into the solid state series MacIntosh's that also use a type of Autoformer on their outputs, but without the benifits of using them within the amps feedback loop, to keep the (damping factor, phase shifts, etc) in check.

Cheers George
unsound
7,329 posts
 
There are many, many speaker cables to choose from. I'm confident that one would find many (if not most) will work just fine with a 4 Ohm load speaker.
More to discover