2. analog
  3. 1401062254

Graham Phantom Anti-Skate. Is it effective at all?

I've had my Phantom Supreme over a year now, and for the most part it's been a pleasure. Beautiful build & sound; awesome VTA and azimuth adjustments. My main hangup had been the headshell; getting a Koetsu to sit flat on the 10" wand seemed impossible because the correct overhang pushed it all the way to the back, behind the main headshell points of contact. Finally I just used 2 plastic washers as shims to get a nice flat mount.

Now my main concern is the anti-skate. I'm not sure if all Phantoms are this way or if it's an issue with my unit. I can't seem to get an effective amount of anti-skate. My preferred method for adjusting anti-skate is to drop the needle in some dead-wax before the label (NOT into a lead-out groove) and adjust so that the stylus creeps *slowly* inwards. With my Graham, I cannot achieve that...it always moves quickly inwards no matter how far out I set the weight. Even physically pushing down on the weight doesn't seem to have much effect in swinging the arm. To me, this seems like the mechanism is not effective, as if I'm running without any compensation. This is very unlike my experiences with a Fidelity Research FR64fx (weight and fishing line) and Clearaudio Magnify (magnetic) -- both have a very noticeably effective anti-skate mechanism, which I can easily dial-in as described above. In fact I just setup a Magnify...it was great!

On my Graham, the pulley & rope system seems to be correctly in place. But without a 2nd until to examine, I can't determine whether this is normal. Could other owners/users of Graham please comment on their experiences with its anti-skate? The situation is OK for now -- I burn hours on my good cartridges very slowly and sparingly -- but I'd rather not have my nice cartridge seeing asymmetric wear over the long-run.

-- Mike
128x128mulveling
dougdeacon
3,338 posts
 
... Graham did not change the Arch Angle of these tubes.
Whaaaat??? They offer longer armwands to reduce tracking angle error but neglect to reduce the headshell offset angle? If so, that's brainless.

All the more reason to follow Philb777's advice: get a Feickert or Mint protractor. I have a Mint. The improvement it made to my alignment and sonics was not subtle. It's a professional's tool. The jigs and protractors supplied by Graham, TriPlanar and the like are toys by comparison.

P.S. Agree with Stringreen and Psag. Anti-skating isn't that important, and in my system it clearly degrades sonics. The longer the armtube the less important it becomes... assuming of course that the cartrdige is actually aligned at the correct zenith angle (which apparently will not be parallel to the headshell... oy!)
rockitman's avatar
rockitman
417 posts
 
Graham did not change the Arch Angle of these tubes.
Whaaaat??? They offer longer armwands to reduce tracking angle error but neglect to reduce the headshell offset angle? If so, that's brainless.

What Syntax is saying is simply not true. Maybe it was on old Graham arms. I have both the 10" & 12" supreme arms. The headshell angle is not the same for the 10&12 arm wands (angle reduced on the 12") and the alignment jigs are also different for obvious reasons. It time for Syntax to stop spreading around misinformation with regard to Graham arms.
syntax's avatar
syntax
2,193 posts
 

It time for Syntax to stop spreading around misinformation with regard to Graham arms.

Honey, I had Graham Arms before you even did know how to spell that name correctly .... Last week there was the High End Show in Germany and I saw these Arms and I even stacked them to see what was going on.
And let's remember that your so called "knowledge" is based on nothing. It was me who told you that your 10" Arm Alignment with your Clearaudio table was wrong. Before you got that information you told everyone how great that Performance is.
Maybe you have different wands, who knows, Fact is, there are others out there, even today (or until last week).
rockitman's avatar
rockitman
417 posts
 
well I have two empty supreme arm wands...10" and 12". They don't line up...it's not even close angle wise. Perhaps you should pull your head out of your arse and stop talking about your first hand experience with old Graham tonearms. It is 2014...your claims that the 12" angle is the same as the 10" head shell angle is patently false. Your supposed facts are sheet.
dougdeacon
3,338 posts
 
Syntax and Rockitman,

Thanks for sharing your experiences. It seems that some Graham armwands may be angled differently than others. That is useful information... caveat emptor.

That said, having these different experiences hardly justifies personal invective. As you're posting publically I presume you're hoping to sway opinions. Indulging in insults will do that, but perhaps not in your favor. Please stop.
More to discover