Infinity RS1 Servo problem

"... so you can sent just a bass signal to it you said you have it set to 100 hz? does that mean you have a dbx now and are using it..."
No, I have the Infinity controller LOW PASS CUTOFF set at LOW. The literature says that is 100HZ.

"...its stereo and mono so be sure to follow the stereo connections..."
I read the owners manual on the web, I understand how it gets connected. Heck, if you can hook up the Infinity box and not blow up your system, you can hook anything up, lol.

"...the speaker setup you stated must sound pretty good. ml panels for the top and infinity bass columns for the bottom.."
I run a pair of AES six pack tube amps and a Cary SLP-98 preamp on the top and a Parasound A21 for the bass. Yes, it's not bad but a tad on the bright side. I need to put it in a bigger/softer room.

"...i have been in audio for 40 years and to me all decent amps (and im not talking comparing a $800 amp to a $4,000 amp. sound very close. unless something is really off i just cant tell..."
40 plus years for me also. Yes, a lot of good amps sound very much the same. The biggest differences are in the bottom end and the top end.

Thanx again.

I got the DBX crossover today. Got it all plugged in and running. It took a few minutes to get the settings in the ball park but I seem to have a handle on it now. I ordered the DBX223XL with XLR connectors. I used XLR to RCA adapters mostly because I had some on hand and just needed two more adapters to finish the connections (six total). I'm not the golden eared audiophile I use to be and I didn't have a lot of hours playing the Infinity towers in my system. However, I am pleased with the results. Once set properly I seem to have the same performance as the original Infinity crossover. If I'm missing some extension, I can't tell, it goes subsonic with ease. At least at the volume levels I listen to. I have the crossover point set at around 70 Hz and that seems to work for my system.
For the guys that have never heard one of the big Infinity tower systems or the big Genesis systems you have no idea how awesome and full scale these systems sound. It's a rare treat and to duplicate that sound cost tens of thousands of dollars. I bought the towers from my brother for 1500 bucks. Thanks for the tip Tomtab, I'm back up and running and all in all I'm very happy with the results.

good to hear russ69. set at 70hz,wow that's pretty low.im set at about 150hz with the infinity mid/tweeter panels. that's all you have to go up to,to blend in with the m,logan panels. im surprised you went with the xlr model since you had to adapt to rca's anyway. whats nice though is you can set the overall volumn now between both panels. glad you are happy with the results. like you I dident think I lost anything the factory xover had to offer also. so if you get the infinity xover fixed would you be in a rush to go back??

Tomtab,

70Hz works for me but the woofers in the ML are still active not like your system where the EMIMs come in at 150Hz so the lower setting works in my system. The blend is very good. The DBX is part of the pro line so it has either 1/4 inch cables or XLRs, the XLRs work for my system, not so much for the 1/4 cables.
Sound quality wise yes I'm happy with the crossover vs the Infinity Servo. I don't think I've lost anything but I don't have any data to back that up. I don't think I'm going to repair the Infinity unit, I'm just going to put a note on it or give it to my nephew as a 3rd spare for his RS1Bs.

Thanx again.

Without the Infinity Servo crossover, the bass towers roll off at 12db/octave below 60Hz. This can be fixed with a digital shelf filter (or an analogue one), but using the DBX or Rane crossover without some equalization throws away the low bass. If you try to fix this with a bass level control, you'll have a peak between 60Hz and 150Hz.